Contents:
Description and Operation
| 1. |
Forward Collision - Avoidance Assist (FCA) : This function may help automatically bring the vehicle to a
stop or with avoidance steering if the preceding vehicle suddenly slows down, or if a forward collision risk
is detected, such as a stopped vehicle, a pedestrian, or a cyclist in front.
|
•
|
Basic Function : If the preceding vehicle suddenly slows down, or if a forward collision risk is
detected, such as a stopped vehicle, a pedestrian, or a cyclist in front, FCA provides a warning.
After the warning, if the risk of collision increases, FCA automatically assists with emergency
braking.
|
|
•
|
Forward Collision - Avoidance Assist - Junction Turning (FCA - JT) : Warns if the left turn
signal switch is activated at an intersection and the risk of collision with an oncoming vehicle
from an adjacent lane is detected while turning left. Automatically assists with braking if the risk
of collision increases after warning.
|
|
| 2. |
Lane Keeping Assist (LKA) : Warns if a lane departure is detected without a turn signal switch on.
Automatically assists steering to prevent the vehicle from departing the lane only if lane departure is
detected without a turn signal switch on.
|
| 3. |
Lane Following Assist (LFA) : Recognizes the lane ahead keeping the vehicle in the center of the lane.
|
| 4. |
Smart Cruise Control with Stop & Go (SCC w/S&G) : SCC helps maintain distance from the vehicle
ahead and drive at a speed set by the driver. It also automatically stops when the car in front stops and
automatically starts when the car in front departs. If a period of time has elapsed, start again by pressing
the accelerator pedal or operating the + / - switch.
|
•
|
A : keeps at a certain distance. (Driving at the speed of the vehicle ahead)
|
|
•
|
B : Constant speed drive at set speed.
|
|
•
|
C : Automatic deceleration.
|
|
|
| 5. |
Navigation - based Smart Cruise Control (NSCC) : NSCC helps drive at a safe speed on the highway using
navigation. If the driver sets the set speed to the current speed limit on the highway during NSCC
operation, the set speed changes automatically whenever the speed limit changes.
| (1)
|
Navigation - based Smart Cruise Control - Curve Zone (NSCC-C) : In a highway curved section, the
speed is automatically reduced appropriately before entering the curve. When leaving the curve, the
speed is returned to the previous setting.
|
•
|
B : Deceleration at safe speed
|
|
•
|
C : Acceleration at set speed
|
|
|
|
| 6. |
Highway Driving Assist (HDA) : HDA helps maintain a set distance and speed from the vehicle ahead when
driving on a highway and helps center the vehicle in the lane while driving, even through a curve.
|
| 7. |
Blind-Spot Collision Warning (BCW) : It detects blind spots and rear high-speed approach vehicles when
driving and warns drivers.
|
| 8. |
Blind-Spot Collision - Avoidance Assist (BCA) : When operating the turn signal switch to change lanes, if
there is a risk of collision with a rear side vehicle, BCA provides a warning. After the warning, if the
risk of collision increases, BCA automatically controls the vehicle to help avoid a collision.
| (1)
|
BCA (Driving) : When operating the turn signal switch to change lanes, if there is a risk of
collision with a rear side vehicle, BCA provides a warning. After the warning, if the risk of
collision increases, BCA automatically controls the vehicle to help avoid a collision.
|
| (2)
|
Exiting a parallel parking : If exiting a parallel parking spot and there is a risk of collision
with a rear side vehicle, BCA automatically assists with emergency braking.
|
|
| 9. |
Safe Exit Warning (SEW) : When a vehicle approaching from the rear is detected after stopping the vehicle
and the door of the vehicle is opened, it warns the driver with a crash warning phrase and a warning sound
on the instrument panel.
|
| 10. |
Safe Exit Assist (SEA) : When the occupant opens the door to exit the vehicle after a stop, if an
approaching vehicle from the rear side is detected, SEA provides a warning. SEA also helps keep the rear
door closed through operation of the electronic child lock.
|
| 11. |
Driver Attention Warning (DAW) : DAW displays the driver’s attention level while driving. Provides a
warning when signs of driver inattentiveness are detected, and recommends a rest if needed.
|
| 12. |
Leading Vehicle Departure Alert (LVDA) : It notifies you when the vehicle ahead departs while at a stop
or traffic light.
|
| 13. |
High Beam Assist (HBA) : HBA recognizes the ambient light and illuminance, such as the lamp of an
opposite vehicle or preceding vehicle, and automatically turns the high beam On/Off.
|
| 14. |
Intelligent Speed Limit Assist (ISLA) : ISLA warns if driving over the speed limit of the road using the
information of the front view camera or navigation. Set speed can be changed according to the speed limit
during MSLA or SCC operation.
|
Components and Components Location
1. Front View Camera 2. Front Radar
|
3. Rear Corner Radar
|
Rear Corner Radar Specification
Item
|
Specification
|
Rated voltage (V)
|
11.5 - 12.5
|
Operating voltage (V)
|
9 - 16
|
Quantity
|
2
|
Max. distance [m (ft.)]
|
70 (229.66)
|
Rear Corner Radar On Vehicle Inspection
Visual Inspection
If there is a problem with BCW / BCA / SEA / RCCW / RCCA, check the items below.
| 1. |
Checking bumper cleanliness: If the bumper is contaminated with snow or dust, performance will be
reduced.
|
| 2. |
Check the condition around the bumper : Warning lights may occur if metal stickers or foreign substances
are attached to the radar.
|
| 3. |
Checking bumper geometry or mounting status : Warning lights may occur if bumper or radar is not properly
installed after an accident.
|
| 4. |
Check the operation status of the switch: Press the switch to check whether the LED works.
|
Diagnosis with KDS
| 1. |
The advanced driver assistance system (driving) can be more quickly diagnosed for problems with the KDS.
(Refer to "DTC guide")
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
|
| (2)
|
S/W Management : Controlling other features including system option setting and zero point
adjustment.
(S/W Management → Rear Corner Radar → Variant Coding)
(S/W Management → Rear Corner Radar → BCW(BSD) Radar Calibration)
|
|
Refer to the KDS screen for operating conditions and details.
|
|
| 2. |
Check the bumper, bracket, or radar when a diagnostic trouble code occurs.
|
•
|
Bumper : Mounting state, bumper external deformation.
|
|
•
|
Radar bracket : Mounting status, radar bracket deformation.
|
|
•
|
Radar : Poor radar nut engagement, radar debris contamination.
|
|
Rear Corner Radar Connector And Terminal Function
| Connector And Terminal Function |
[Rear Corner Radar]
Pin No
|
Master Unit (LH)
|
Slave Unit (RH)
|
1
|
Battery ( + )
|
Battery ( + )
|
2
|
L-CAN (High)
|
L-CAN (High)
|
3
|
C-CAN (Low)
|
C-CAN (Low)
|
4
|
BCW Warning indicator
|
BCW Warning indicator
|
5
|
-
|
-
|
6
|
L-CAN (Low)
|
L-CAN (Low)
|
7
|
C-CAN (High)
|
C-CAN (High)
|
8
|
Ground ( - )
|
Ground ( - )
|
[BCW & RCCW Indicator]
Pin No
|
Connector
|
1
|
Mirror actuator vertical (UP/DOWN)
|
2
|
Mirror actuator COMMON
|
3
|
Mirror actuator horizontal (LEFT/RIGHT)
|
4
|
Mirror heater ( + )
|
5
|
Mirror heater ( - ) / Side repeater ( - )
|
6
|
Mirror folding
|
7
|
Mirror unfolding
|
8
|
Side repeater ( + )
|
9
|
-
|
10
|
BCW Indicator ( - )
|
11
|
BCW Indicator ( + )
|
12
|
-
|
13
|
-
|
14
|
-
|
15
|
-
|
16
|
-
|
17
|
-
|
18
|
-
|
19
|
-
|
Rear Corner Radar Removal
Rear Corner Radar
|
If the rear corner radar is damaged, replace only therear corner radar.
|
| 1. |
Remove the rear bumper assembly.
(Refer to Body - "Rear Bumper Assembly")
|
| 2. |
Disconnect the rear corner radar connector (A).
|
| 3. |
Remove the rear corner radar (A) after removing the nuts.
Tightening torque :
8.8 - 10.8 N·m (0.9 - 1.1 kgf·m, 6.5 - 8.0 lb·ft)
|
|
|
The rear corner radar will not operate normally if the bracket or radar is damaged.
|
Extension Wiring
|
If the extension wiring or connector is damaged, replace only the extension wiring.
|
| 1. |
Remove the rear bumper assembly.
(Refer to Body - "Rear Bumper Assembly")
|
| 2. |
Disconnect the extension wiring connector (A).
|
| 3. |
Remove the extension wiring (A) after removing the clip.
|
Clip position :
|
|
Rear Corner Radar Bracket
|
If the rear corner radar bracket is damaged, replace only the rear corner radar bracket.
|
| 1. |
Remove the rear corner radar.
(Refer to Rear Corner Radar - "Removal")
|
| 2. |
Remove the rear corner radar bracket (A) after removing the nuts.
Tightening torque :
8.8 - 10.8 N·m (0.9 - 1.1 kgf·m, 6.5 - 8.0 lb·ft)
|
|
|
The rear corner radar will not operate normally if the bracket or radar is damaged.
|
BCW & RCCW indicator
| 1. |
Disconnect the battery negative ( - ) terminal.
|
| 2. |
Remove the mirror (A) by applying slight force, after inserting a remover as shown below.
|
| 3. |
Disconnect the mirror heater connectors (A) and BCW & RCCW indicator connector (B).
|
Rear Corner Radar Installation
Rear Corner Radar
| 1. |
Install in reverse order of removal.
|
1) Parts number
2)RL (Rear - Left side), RR (Rear - Right side)
|
|
| 2. |
Perform the order below with the KDS when replacing the rear corner radar unit.
(S/W Management → Rear Corner Radar → Variant Coding)
|
Refer to the KDS screen for operating conditions and details.
|
|
| 3. |
Perform the rear corner radar mounting angle calibration procedure.
(Refer to Rear Corner Radar - "Adjustment")
|
BCW & RCCW indicator
| 1. |
Install in reverse order of removal.
|
Rear Corner Radar Adjustment
Rear Corner Radar Calibration Inspection
|
•
|
Check the rear corner radar mounting angle when replacing the bracket or any components of rear corner
radar.
|
|
•
|
Check the rear corner radar mounting angle when a vehicle equipped with the rear corner radar system has
a rear or side collision.
|
Check Before Rear Corner Radar Calibration
| 1. |
When a failure code [C270854], [C270954] occurs, check the following before performing calibration.
|
| 2. |
Check the vehicle condition and whether the rear corner radar unit or bracket is deformed (mounting
angle, twisted vehicle body, etc.).
Vehicle Check
|
Normal
|
Abnormal (deformation of the bracket or bolted area)
|
|
|
|
Vehicle Check
|
Normal
|
Abnormal (deformation of the bracket or bolted area)
|
|
|
|
|
| 3. |
Check the nut tightening and if there is any foreign substance.
Vehicle Check
|
Normal
|
Abnormal (deformation of the bracket or bolted area)
|
|
|
|
|
Tool Name / Number
|
Illustration
|
Description
|
Rear Corner Radar Correction Tool Set 09958 - 3T500
|
|
Used to correct the rear corner radar unit.
|
Vertical Plumb 09958 - 3T010
|
|
Used to correct the rear corner radar unit. Used to create a center line.
|
Spirit Level 09958 - 3T070
|
|
Used to measure the rear corner radar horizontal angle.
|
Rear Corner Radar Fixing Adaptor 09958 - 3T080
|
|
Used to measure the horizontal angle.
|
Digital Protractor 09958 - 3T090
|
|
Used to measure the horizontal angle.
|
Digital Inclinometer 09958 - 3T100
|
|
Used to correct the rear radar unit. Used to measure the vertical angle.
|
Rear Corner Radar Calibration
|
Check the items below before performing the rear corner radar
calibration.
|
•
|
Park the vehicle on flat ground.
|
|
•
|
Check that the radar surface is clean.
|
|
•
|
Check the suspension for damage.
|
|
•
|
Check the tire alignment.
|
|
•
|
Check the tire pressure.
|
|
| 1. |
Remove the rear bumper assembly.
(Refer to Body - "Rear Bumper Assembly")
|
| 2. |
Mark the center point (A) after measuring the distance on top of the hood assembly.
|
| 3. |
Attach a vertical plumb (09958 - 3T010) on the roof panel, and lower the plumb (A) to the ground so that
it passes through the center of the emblem.
|
| 4. |
Mark the center point below the plumb (A).
|
| 5. |
Attach a vertical plumb (09958 - 3T010) on the roof panel, and lower the plumb (A) to the ground so that
it passes through the center of the emblem.
|
| 6. |
Mark the center point below the plumb (A).
|
| 7. |
Making the center line of the vehicle using a string.
| (1)
|
Pass the string through the bottom of the vehicle from the rear of the vehicle to the front and
fix the string to the center point (A) of the front of the vehicle.
|
| (2)
|
Fix the string to the point (C) about 1.5 - 2 m (4.95 - 6.6 ft) from the back of the vehicle so
that it passes the rear center point (B).
|
|
| 8. |
Remove the rear corner radar.
(Refer to Rear Corner Radar - "Removal")
|
| 9. |
Refit the rear corner radar unit fixing adapter (special tool: 09958 - 3T080) to the rear radar unit and
secure the horizontal laser (special tool: 09958 - 3T070).
|
| 10. |
Measure the angle (C) between the center line (A) of the angle measuring and the horizontal laser beam
(B) using a digital protractor (09958 - 3T090).
|
| 11. |
Measure the vertical angle of the rear radar unit using a digital horizontal system (special tool: 09958
- 3T100).
|
•
|
Make sure to perform the zero setting horizontally before using a digital inclinometer.
|
|
•
|
Note that depending on the display method of the digital inclinometer, the ( + ) / ( - )
angle may be displayed differently.
|
|
|
| 12. |
If the measured values deviate from the specified values, insert a washer (A) between the bracket of the
rear corner radar unit.
Specifications
Horizontal angle : 57°
Vertical angle : 93°
|
|
| 13. |
install the rear corner radar.
(Refer to Rear Corner Radar - "Removal")
|
| 14. |
Install the rear bumper assembly.
(Refer to Body - "Rear Bumper Assembly")
|
Check that the rear corner radar is clean before installing the rear bumper assembly.
|
|
| 15. |
Perform the order below with the KDS.
(S/W Management → Rear Corner Radar → BCW(BSD) Radar Calibration)
|
Refer to the KDS screen for operating conditions and details.
|
|
Front Radar Specification
Item
|
Specification
|
Rated voltage (V)
|
11.5 - 12.5
|
Operating voltage (V)
|
9 - 16
|
Mounting angle (°)
|
Horizontal
|
-0.8 to 0.8
|
Vertical
|
-0.4 to 0.4
|
Front Radar On Vehicle Inspection
Visual inspection
If there is a problem with the front radar check the items below.
| 1. |
Checking bumper cleanliness : If the bumper is contaminated with snow or dust, may be disable during
operation.
|
| 2. |
Check the condition around the bumper : Warning lights may occur if metal stickers or foreign substances
are attached to the radar.
|
| 3. |
Checking bumper geometry or mounting status : Warning lights may occur if bumper or radar is not properly
installed after an accident.
|
Diagnosis with KDS
| 1. |
The advanced driver assistance system (driving) can be more quickly diagnosed for problems with the KDS.
(Refer to "DTC guide")
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
|
| (2)
|
S/W Management : Controlling other features including system option setting and zero point
adjustment.
(S/W Management → Front Radar → Inspection/correction of the front - radar mounting angle → C1
(Stop mode)
(S/W Management → Front Radar → Inspection/correction of the front - radar mounting angle → C2
(Driving mode))
|
|
Refer to the KDS screen for operating conditions and details.
|
|
| 2. |
Check the bumper, bracket, or radar when a diagnostic trouble code occurs.
|
•
|
Bumper : Mounting state, bumper external deformation.
|
|
•
|
Radar bracket : Mounting status, radar bracket deformation.
|
|
•
|
Radar : Poor radar nut engagement, radar debris contamination.
|
|
Front Radar Connector And Terminal Function
| Connector And Terminal Function |
Pin No
|
Connector
|
1
|
Ground ( - )
|
2
|
L-CAN (High)
|
3
|
L-CAN (Low)
|
4
|
C-CAN (High)
|
5
|
C-CAN (Low)
|
6
|
IG
|
Front Radar Removal
| 1. |
Remove the front bumper assembly.
(Refer to Body - "Front Bumper Assembly")
|
| 2. |
Disconnect the front radar connector (A).
|
Clip position :
|
|
| 3. |
Remove the front radar (A) after removing the nuts.
Tightening torque :
8.8 - 10.8 N·m (0.9 - 1.1 kgf·m, 6.5 - 8.0 lb·ft)
|
|
Front Radar Installation
|
Check the items below before performing the front radar
calibration.
|
•
|
Park the vehicle on flat ground.
|
|
•
|
Check that the radar surface is clean.
|
|
•
|
Check the suspension for damage.
|
|
•
|
Check the tire alignment.
|
|
•
|
Check the tire pressure.
|
|
| 1. |
Install the front radar (A) after tightening the nuts.
Tightening torque :
8.8 - 10.8 N·m (0.9 - 1.1 kgf·m, 6.5 - 8.0 lb·ft)
|
|
| 2. |
Connect the front radar connector (A).
|
| 3. |
Check the front radar vertical angle by using the digital inclinometer (09958 - 3T100) (A).
Horizontal Angle : 0° ± 0.8°
Vertical Angle : 90° ± 0.4°
|
|
•
|
Make sure to perform the zero setting horizontally before using a digital inclinometer.
|
|
•
|
Note that depending on the display method of the digital inclinometer, the ( + ) / ( - )
angle may be displayed differently.
|
|
|
| 4. |
Adjust to vertical installation angle by turning the adjusting screw (A) of the front radar.
|
–
|
turn clockwise : adjusting ( + ) angle
|
|
–
|
turn counterclockwise : adjusting ( - ) angle
|
|
| 5. |
Install the front bumper assembly.
(Refer to Body - "Front Bumper Assembly")
|
Check that the front radar or radar cover is clean before installing the front bumper assembly.
|
|
| 6. |
Perform the front radar mounting angle inspection / calibration procedure.
(Refer to Front Radar - "Adjustment")
|
Front View Camera On Vehicle Inspection
Diagnosis with KDS
| 1. |
The advanced driver assistance system (driving) can be more quickly diagnosed for problems with the KDS.
(Refer to "DTC guide")
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
|
| (2)
|
S/W Management : Controlling other features including system option setting and zero point
adjustment.
(S/WManagement → Front View Camera → System Identification)
(S/W Management → Front View Camera → Variant Coding)
(S/W Management → Front View Camera → SPTAC Calibration)
|
|
Refer to the KDS screen for operating conditions and details.
|
|
Front View Camera Connector And Terminal Function
| Connector And Terminal Function |
Pin No
|
Connector
|
1
|
-
|
2
|
-
|
3
|
L-CAN (Low)
|
4
|
C-CAN (Low)
|
5
|
-
|
6
|
-
|
7
|
IG
|
8
|
-
|
9
|
L-CAN (High)
|
10
|
C-CAN (High)
|
11
|
Ground ( - )
|
12
|
-
|
Front View Camera Removal
| 1. |
Perform the order below with the KDS before replacing the front view camera.
(S/W Management → Front View Camera → System Identification)
|
Refer to the KDS screen for operating conditions and details.
|
|
| 2. |
Disconnect the battery negative ( - ) terminal.
|
| 3. |
Remove the multi sensor blanking cover (A).
|
Clip position :
|
|
| 4. |
Remove the multi sensor cover (A) in the direction of the arrow.
|
Clip position :
|
|
| 5. |
Disconnect the front view camera connector (A).
|
| 6. |
Remove the front view camera (A) by pulling both hooks.
|
Clip position :
|
|
Front View Camera Installation
| 1. |
Install in reverse order of removal.
|
Check that the front view camera mounting area (windshield glass) is clean before installing the
front view camera.
|
|
| 2. |
Perform the order below with the KDS when replacing the front view camera unit.
(S/W Management → Front View Camera → Variant Coding)
|
Refer to the KDS screen for operating conditions and details.
|
|
| 3. |
Enter the specification value read from the existing camera into the new front view camera.
|
| 4. |
Perform the front view camera unit calibration.
(Refer to Front View Camera - "Adjustment")
|
Front View Camera Adjustment
Tool Name / Number
|
Illustration
|
Description
|
Front View Camera Calibration target 09890 - 3V100
|
|
Used for compensating front view camera unit
|
SCC Setting Beam 09964 - C1200
|
|
Used for front radar unit setting. Used for front view camera unit setting.
|
| Front View Camera Calibration |
|
Perform the front view camera calibration in the following cases.
|
•
|
When the front view camera is reinstallation.
|
|
•
|
When the front view camera bracket is deformed.
|
|
•
|
When the front view camera is replaced.
|
|
•
|
When the windshield glass is replaced.
|
|
•
|
When the DTC occurs for the front view camera.
|
Check the items below before performing the front view camera
calibration.
|
•
|
Park the vehicle on flat ground.
|
|
•
|
Check that the windshield glass is clean.
|
|
•
|
Check the suspension for damage.
|
|
•
|
Check the tire alignment.
|
|
•
|
Check the tire pressure.
|
|
Front View Camera Service Point Target Auto Calibration (SPTAC)
| 1. |
Mark the center point (A) after measuring the distance on top of the windshield glass.
|
| 2. |
Install the SCC setting beam (09964 - C1200) in the center of the roof above the windshield glass of the
vehicle (same for both short and long distance calibrations).
|
| 3. |
Allow the beam of the SCC setting beam (09964 - C1200) to pass through the center of the emblem.
|
The level laser must be set to 'ON' and the holding (locking) function is not used.
|
|
| 4. |
The height of the front view camera calibration target (09890 - 3V100) is adjusted to be 90 ± 2 cm (36 ±
0.8 in.) from the ground.
|
| 5. |
Place the front view camera calibration target (09890 - 3V100) so that it maintains a distance of 0 cm (0
in.) from the bumper. [Maximum tolerance : 10 cm (4 in.)]
|
| 6. |
Install the front view camera calibration target (09890 - 3V100) center (A) in line with the laser
vertical line of the SCC setting beam (09964 - C1200). [Maximum tolerance: 5cm (2 in)]
|
•
|
Align the front view camera calibration target (09890 - 3V100) referring to the tolerance
angle below.
|
|
•
|
Tolerance is important and sensitive to floor conditions.
|
|
|
| 7. |
Perform the order below with the KDS.
(S/W Management → Front View Camera → SPTAC Calibration)
|
Refer to the KDS screen for operating conditions and details.
|
|
| 8. |
The height of the front view camera calibration target (09890 - 3V100) is adjusted to be 90 ± 2 cm (36 ±
0.8 in.) from the ground.
|
| 9. |
Place the front view camera calibration target (09890 - 3V100) so that it maintains a distance of 120 cm
(48 in.) from the bumper. (Maximum tolerance : 20 cm (8 in.))
|
| 10. |
Install the front view camera calibration target (09890 - 3V100) center (A) in line with the laser
vertical line of the SCC setting beam (09964 - C1200). [Maximum tolerance: 5cm (2 in)]
|
•
|
Align the front view camera calibration target (09890 - 3V100) referring to the tolerance
angle below.
|
|
•
|
Tolerance is important and sensitive to floor conditions.
|
|
|
| 11. |
Perform the order below with the KDS.
(S/W Management → Front View Camera → SPTAC Calibration)
|
Refer to the KDS screen for operating conditions and details.
|
|
| 12. |
Check the DTC and warning lamp after erasing the DTC with the KDS.
|
Driver Driving Assistance Switch Connector And Terminal Function
| Connector And Terminal Function |
Pin No
|
Connector
|
1
|
Trip switch 1 input ( + )
|
2
|
Trip switch 2 input ( + )
|
3
|
ILL ( + )
|
4
|
-
|
5
|
ILL ( - )
|
6
|
Trip switch input ( - )
|
Driver Driving Assistance Switch Removal and Installation
| Driver Driving Assistance Switch |
| 1. |
Remove the steering wheel remote controller. [RH]
(Refer to Body Electrical System - "Steering Wheel Remote Controller
(SWRC)")
|
| 1. |
Install in reverse order of removal.
|
Other information:
Kia Seltos SP2 (2021-2026) Service Manual: AWD mode
AWD mode helps improve the driving performance of the Kia Seltos by controlling power delivery to all four wheels. This system supports better traction and stability when road conditions change, especially on wet, slippery, sandy, muddy, or uneven surfaces.
You can switch from AWD AUTO mode to AWD Lock mode by pressing the AWD Lock mode switch.
Kia Seltos SP2 (2021-2026) Service Manual: Personalized Profile and Vehicle Settings
When a registered digital key is linked to a user profile, the Kia Seltos can automatically apply selected vehicle settings when that digital key is used. This may include door lock and unlock behavior with Digital Key 2 Touch and other personalized settings available through the infotainment system.
User profile linking and personalization are available for up to two drivers, allowing the Kia Seltos to provide a more convenient and customized driving experience for regular users.