Owner's library Kia Seltos Manuals Owner's manual pages, service notes, maintenance references and practical Kia Seltos help in one clean library.

Kia Seltos reference pages

Manuals, maintenance notes and quick owner help.

Find Kia Seltos operating instructions, warning light explanations, service information and owner guidance without digging through a full PDF.

Kia Seltos SP2 (2021-2026) Service Manual / Maintenance / Body / Air Conditioner Refrigerant/Compressor Refrigerant Recovery/Recycling/Charging/Vacuum

Kia Seltos: Body / Air Conditioner Refrigerant/Compressor Refrigerant Recovery/Recycling/Charging/Vacuum

Refrigerant Recovery/Recycling/Charging/Vacuum (R-134a)
Equipped with R-134a recovery/recycling/charging equipment
1.
Connect the R-134a recovery/recycling/charging equipment to the high-pressure service port (A) and low-pressure service port (B) by reading the refrigerant recovery/recycling/charging equipment instruction manual.

Maintenance — Body / Air Conditioner Refrigerant/Compressor / Refrigerant Recovery/Recycling/Charging/Vacuum / Refrigerant Recovery/Recycling/Charging/Vacuum (R-134a) illustration

Note    
Refrigerant charging equipment should be installed on a flat surface so that it is easy to recover the refrigerant and in particular, the refrigerant can be accurately injected.
Refrigerant recovery operation
Use only service equipment that is U.L-listed and is certified to meet the requirements of SAE J2210 to remove HFC-134a (R-134a) from the air conditioning system.
Note    
•
Air conditioning refrigerant or lubricant vapor can irritate your eyes, nose, or throat.
•
Be careful when connecting service equipment.
•
Do not breathe refrigerant or vapor.
If accidental system discharge occurs, ventilate work area before resume of service.
Additional health and safety information may be obtained from the refrigerant and lubricant manufacturers.
1.
Measure the amount of refrigerant oil removed from the A/C system after the recovery process is completed. Be sure to install the same amount of new refrigerant oil back into the A/C system before charging.
Refrigerant system vacuum operation
Use only service equipment that is U.L-listed and is certified to meet the requirements of SAE J2210 to remove HFC-134a (R-134a) from the air conditioning system.
Note    
•
Air conditioning refrigerant or lubricant vapor can irritate your eyes, nose, or throat.
•
Be careful when connecting service equipment.
•
Do not breathe refrigerant or vapor.
If accidental system discharge occurs, ventilate work area before resume of service.
Additional health and safety information may be obtained from the refrigerant and lubricant manufacturers.
1.
When an A/C System has been opened to the atmosphere, such as during installation or repair, it must be evacuated using an R-134a refrigerant Recovery / Recycling / Charging System. (If the system has been open for several days, the receiver / dryer should be replaced, and the system should be evacuated for several hours.)
2.
Connect an R-134a refrigerant
Recovery / Recycling / Charging System to the high-pressure service port and the low-pressure service port as shown, following the equipment manufacturer's instructions.
3.
If the low-pressure does not reach more than 93.3 kPa (700 mmHg, 27.6 in.Hg) in 10 minutes, there is probably a leak in the system. Partially charge the system, and check for leaks (see Refrigerant Leak Test).
4.
Remove the low pressure valve from the low-pressure service port.
Refrigerant charge
Use only service equipment that is U.L-listed and is certified to meet the requirements of SAE J2210 to remove HFC-134a (R-134a) from the air conditioning system.
Note    
•
Air conditioning refrigerant or lubricant vapor can irritate your eyes, nose, or throat.
•
Be careful when connecting service equipment.
•
Do not breathe refrigerant or vapor.
If accidental system discharge occurs, ventilate work area before resume of service.
Additional health and safety information may be obtained from the refrigerant and lubricant manufacturers.
1.
Connect an R-134a refrigerant
Recovery / Recycling / Charging System to the high-pressure service port as shown, following the equipment manufacturer's instructions.
2.
Add the same amount of new refrigerant oil to system that was removed during recovery. Use only specified refrigerant oil. Charge the system with R-134a refrigerant. Do not overcharge the system the compressor will be damaged.

Regulated refrigerant amount : 500 ± 25 g (17.6 ± 0.88 oz.)

Leak test of refrigerant
Always conduct a leak test with an electronic leak detector whenever leakage or refrigerant is suspected and when conducting service operations which are accompanied by disassembly or removing or connection fittings.
Information    
In order to use the leak detector properly, read the manual supplied by the manufacturer.
If a gas leak is detected, proceed as follows:
1.
Check the torque on the connection fittings and, if too loose, tighten to the proper torque. Check for gas leakage with a leak detector.
2.
If leakage continues even after the fitting has been tightened, discharge the refrigerant from the system, disconnect the fittings, and check their seating faces for damage. Always replace, even if the damage is slight.
3.
Check the compressor oil and add oil if required.
4.
Charge the system and recheck for gas leaks. If no leaks are found, evacuate and charge the system again.
Refrigerant Recovery/Recycling/Charging/Vacuum (R-1234yf)
Equipped with R-1234yf recovery/recycling/charging equipment
1.
Connect the R-1234yf recovery/recycling/charging equipment to the high-pressure service port (A) and low-pressure service port (B) by reading the refrigerant recovery/recycling/charging equipment instruction manual.

Maintenance — Body / Air Conditioner Refrigerant/Compressor / Refrigerant Recovery/Recycling/Charging/Vacuum / Refrigerant Recovery/Recycling/Charging/Vacuum (R-1234yf) illustration

Note    
Refrigerant charging equipment should be installed on a flat surface so that it is easy to recover the refrigerant and in particular, the refrigerant can be accurately injected.
Refrigerant recovery operation
1.
With the high and low pressure valves open, the refrigerant is recovered by using R-1234yf recovery/recycling/charging equipment.
Note    
•
Refrigerant recovery too quickly causes compressor oil to drain from the system.
•
Never disconnect the air conditioning system until the refrigerant has been completely recovered. If it is separated before the recovery of the refrigerant is completed, the refrigerant and oil are discharged into the vehicle by the pressure in the air conditioner system, which causes contamination.
•
Refrigerant recovery must be performed with the high and low pressure valves opened. If only one valve is opened, the refrigerant recovery time increases.
2.
Measure the amount of compressor oil drained from the air conditioner system after the recovery operation is completed. Supplement the compressor oil drained when charging the air conditioner refrigerant.
Refrigerant system vacuum operation
Note    
When charging the refrigerant, the air conditioner system must be evacuated. This evacuating operation is performed to remove all the air and moisture that have flowed into the unit, and the system vacuums for more than 10 minutes after each part is installed.
1.
Perform the vacuum by using R-1234yf recovery/recycling/charging equipment while the high and low pressure valves open.
2.
If the gauge remains in the vacuum zone for 10 minutes while the high and low pressure valves closed, vacuum has been performed normally. If the pressure increases, it is a leak in the system, so repair the leak by the following order.
(1)
Charging the system with refrigerant charging equipment. (Refer to Refrigerant charging)
(2)
Check the refrigerant leak with leak detector and repair if leak is found. (Refer to Refrigerant leak test)
(3)
Drain the refrigerant again and evacuate the system.
3.
After evacuating for more than 10 minutes, check the vacuum and close both high and low pressure valves. This state is ready for charging.
Note    
Compressor oil must be applied to the O-ring when assembling air conditioner parts, and cleanliness must be maintained to avoid foreign substances, especially gloves.
Refrigerant charge
1.
Replenish the amount of discharged compressor oil by using R-1234yf recovery/recycling/charging equipment while the high pressure valve is opened after evacuating the air conditioner system.
Note    
If additional oil is not added when charging the refrigerant, the lubricity deteriorates due to insufficient oil in the system, which cause problem such as compressor sticking.
2.
Charge the refrigerant with specified amount while the high-pressure valve open by using the R-1234yf recovery/recycling/charging equipment and then close the high-pressure valve.

Regulated refrigerant amount : 450 ± 25 g (15.9 ± 0.88 oz.)

Note    
Do not overcharge the refrigerant as there is a risk of damage to the compressor.
3.
Check that the refrigerant is not leaking from the system with leak detector. (Refer to refrigerant leak test)
Refrigerant leak test
When a refrigerant leak is suspected or the connection part is disassembled or loosened, perform the leak test with an electronic leak detector.
1.
Check the torque of the connection part, and if it is too loose, check the gas leak with leak detector after tightening it to the specified tightening torque.
2.
If leakage continues even after re-tightening the connection part, drain the refrigerant and separate the connection part to check the contact surface for damage. If there is even a small damage, replace it with a new one.
3.
Check the compressor oil and add oil if necessary.
4.
Charging the system and check for gas leakage. If there is no problem, evacuate the system before charging.

Other information:

Kia Seltos SP2 (2021-2026) Service Manual: Instrument cluster

Type A Type B * The actual instrument cluster in your Kia Seltos may differ from the illustration depending on trim level, market, and vehicle specifications. Speedometer Tachometer Fuel gauge Engine coolant temperature gauge LCD display Warning and indicator lights

Kia Seltos SP2 (2021-2026) Service Manual: Electronic Parking Brake (EPB) Description and Operation

Description The Electric Parking Brake (EPB) is a parking brake system that operates the actuators of each caliper using an electrical signal via button operation, unlike a parking brake operated by a lever or pedal. The EPB has the function to engage the parking brake when the vehicle is stationary, to assist in braking in emergencies due to brake failure, and to engage the parking brake automatically when the engine off.