Kia Seltos SP2 (2021-2026) Service Manual / Brake System / ESC (Electronic Stability Control) System / Description and Operation
Kia Seltos: ESC (Electronic Stability Control) System / Description and Operation
| Description of ESC |
Electronic Stability Control (ESC) recognizes critical driving conditions, such as panic reactions in dangerous
situations, and stabilizes the vehicle by individual wheel braking and engine control input.
ESC adds an additional function known as Active Yaw Control (AYC) to the ABS, TCS, EBD and ESC functions. On
contrary, the ABS/TCS function controls wheel slip during braking and accelerating, and thus, mainly intervenes in
the longitudinal dynamics of the vehicle, and the active yaw control stabilizes the vehicle on the vertical axis.
This is achieved by individual wheel brake intervention and adaptation of momentary engine torque with no need
for any action to be taken by the driver.
ESC essentially consists of three assemblies : the sensors, the electronic control unit and the actuators.
The stability control feature works under all driving and operating conditions. Under certain driving conditions,
the ABS/TCS function can be activated simultaneously with the ESC function in response to a command by the driver.
In the event of a failure of the stability control function, the basic safety function, ABS, is still maintained.
Description of ESC Control
ESC system consists of ABS/EBD, TCS and AYC functions.
ABS/EBD function : The ECU changes the active sensor signal (current shift) coming from the four wheel sensors
into square waves. By using the input of above signals, the ECU calculates the vehicle speed and the acceleration
& deceleration of the four wheels. And, the ECU determines whether the ABS/EBD should be actuated or not.
TCS function prevents the wheel slip of drive direction by adding the brake pressure and engine torque reduction
via CAN communication. TCS function uses the wheel speed sensor signal to determine the wheel slip as far as ABS
function.
AYC function prevents unstable maneuver of the vehicle. To determine the vehicle maneuver, AYC function uses the
maneuver sensor signals (Yaw Rate Sensor, Lateral Acceleration Sensor, and Steering Wheel Angle Sensor).
If vehicle maneuver is unstable (Over Steer or Under Steer), AYC function applies the brake pressure on certain
wheel, and sends engine torque reduction signal by CAN.
After the ignition on, the ECU continuously diagnoses the system for failures (self-diagnosis). If a system
failure is detected, the ECU informs driver of the system failure through the BRAKE/ABS/ESC warning lamp (fail-safe
warning).
Input and Output Diagram
| ESC Operation Mode |
| 1. |
ESC Non-operation : Normal braking.
|
| 2. |
ESC operation
|
||||||||||||||||||||||
Warning Lamps
|
Lamp |
Name |
|
|
ABS Warning Lamp |
|
|
EBD / Parking Brake Warning Lamp |
|
|
ESC Operating / Warning Lamp |
|
|
ESC OFF Lamp |
|
|
EPB Warning Lamp |
ABS Warning Lamp Module
The active ABS warning lamp module indicates the self-test and failure status of the ABS. The ABS warning lamp is
turned on under the following conditions:
| – |
During the initialization phase after IGN ON. (continuously for 3 seconds).
|
| – |
In the event of ABS function failure.
|
| – |
During diagnostic mode.
|
| – |
When the communication between HECU and PCM has failed.
|
| – |
Cluster lamp is ON when communication is impossible with CAN module.
|
EBD/Parking Brake Warning Lamp Module
The active EBD warning lamp module indicates the self-test and failure status of the EBD. However, in case the
Parking Brake Switch is turned on, the EBD warning lamp is always turned on regardless of EBD functions. The EBD
warning lamp is turned on under the following conditions:
| – |
During the initialization phase after IGN ON. (continuously for 3 seconds).
|
| – |
When the Parking Brake Switch is ON or brake fluid level is low.
|
| – |
When the EBD function has a failure.
|
| – |
During diagnostic mode.
|
| – |
When the communication between HECU and PCM has failed.
|
| – |
Cluster lamp is ON when communication is impossible with CAN module.
|
ESC Function/Warning Lamp
The ESC function/warning lamp indicates the self-test and failure status of the ESC.
The ESC function/warning lamp is turned on under the following conditions:
| – |
During the initialization phase after IGN ON. (continuously for 3 seconds).
|
| – |
When the ESC function is inhibited by system failure.
|
| – |
When the ESC control is operating. (Blinking - 2Hz)
|
| – |
During diagnostic mode (except standard mode).
|
| – |
Cluster lamp is ON when communication is impossible with CAN module.
|
ESC Off Lamp
The ESC Off lamp indicates the self-test and operating status of the ESC.
The ESC Off lamp operates under the following conditions :
| – |
During the initialization mode after IGN ON. (continuously for 3 seconds).
|
| – |
ESC Off lamp is ON when driver turns OFF ESC switch.
|
ESC On/Off Switch
The ESC On/Off Switch is used to toggle the ESC function between On/Off states based upon driver input.
The On/Off switch is a normally open, is a momentary contact switch.
Initial status of the ESC function is ON.
Other information:
Kia Seltos SP2 (2021-2026) Service Manual: Explanation of scheduled maintenance items
The following components require scheduled maintenance to help keep the Kia Seltos reliable, efficient, and safe during daily driving. Regular inspection also helps detect wear or damage before it becomes a larger repair issue. Engine oil and filter The engine oil and oil filter should be replaced at the intervals listed in the Kia Seltos maintenance schedule.Kia Seltos SP2 (2021-2026) Service Manual: General Safety Information and Caution
Precaution (R-134a) When Handling Refrigerant 1. R-134a liquid refrigerant is highly volatile. A drop on the skin of your hand could result in localized frostbite. When handling the refrigerant, be sure to wear gloves. 2. It is standard practice to wear goggles or glasses to protect your eyes, and gloves to protect your hands.