Owner's library Kia Seltos Manuals Owner's manual pages, service notes, maintenance references and practical Kia Seltos help in one clean library.

Kia Seltos reference pages

Manuals, maintenance notes and quick owner help.

Find Kia Seltos operating instructions, warning light explanations, service information and owner guidance without digging through a full PDF.

Kia Seltos: General Information / General Information

Contents:

General Information

General Service Information
1.
Protect the vehicle's protective painted surfaces and internal parts with work covers (seat covers) or tape (if damaged by tools) to prevent damage.
Note    
Before closing the engine hood, check the engine room for any tools or parts left.
2.
At the same time as checking the defective part, determine the cause of the failure, determine whether it is necessary to remove or disassemble, and then work in the order of the workshop manual.
In order to prevent mis-assembly and to facilitate assembly work, punch marks or coincidence marks are applied to areas that do not adversely affect the function or appearance. When disassembling parts with a large number of parts and similar parts, arrange them so as not to be confused during assembly.
1)
Arrange the removed parts in order.
2)
Distinguish between replacement parts and reusable parts.
3)
When replacing bolts and nuts, be sure to use designated standard products.

General Information — General Information / General Service Information illustration

3.
Special tools must be used for work instructing the use of special tools, as the parts may be damaged or damaged if the work is performed by using tools other than special tools.

General Information — General Information / General Service Information illustration

4.
Parts below must be replaced with new ones.
1)
Oil seal
2)
Gasket
3)
Packing
4)
O-ring
5)
Washer
6)
Split pin

General Information — General Information / General Service Information illustration

5.
Parts
1)
When replacing a new part, be sure to use genuine KIA parts.
2)
Use repair parts and the enclosed sets and kits.
3)
Parts supplied as maintenance parts may differ from parts assembled in a vehicle for the unification of parts, so check the parts catalog carefully before performing maintenance work.
6.
Be sure to turn the ignition switch "OFF" and disconnect the battery negative ( - ) cable before replacing or repairing electrical system parts.

General Information — General Information / General Service Information illustration

7.
Be careful not to contact fuel and oil with rubber parts and hoses.

General Information — General Information / General Service Information illustration

Inspection of Battery Terminals And Wiring
1.
Check that the battery terminals are solid.
2.
Check that the battery terminals and wiring are not corroded by battery electrolyte.
3.
Check the battery terminals and wiring for open circuits or the potential to open the circuit.
4.
Check the insulation and sheath of the wiring for damage, cracks, and deterioration of quality.
5.
Check if the terminals of the battery are in contact with other metal parts (car body or other parts).
6.
Make sure that the ground bolt and the body are in full contact.

General Information — General Information / General Service Information illustration

7.
Check the wiring connection.
8.
Make sure that the wiring does not come into contact with sharp edges or hot parts (exhaust manifold, muffler, etc.) on the vehicle body.
9.
Make sure that the wiring is secured with sufficient clearance from rotating parts such as cooling fans and drive belts.
10.
Make sure that the wiring has an adequate vibration margin between vibration parts such as engines and fixed parts such as vehicle bodies.
Inspection of Fuse
1.
Check whether the fuse holder firmly secures the fuse.
2.
Verify that the fuse capacity is appropriate for each circuit.
3.
Inspect the fuse for any signs of damage or malfunction.
Information    
The fuse has an inspection contact, allowing you to check its condition without removing it. To test the fuse, connect one contact of a test lamp to one side of the fuse (one at a time) and ground the other contact. If the lamp lights up, the fuse is proper. (Make sure the ignition switch is in the correct position to allow current to flow through the fuse circuit.)

General Information — General Information / General Service Information illustration

4.
If the fuse is blown or damaged, refer to the electrical circuit diagram and inspect the components connected to the fuse.
5.
If no abnormalities are found in the components, thoroughly check the wiring circuit for any interference or damage.
6.
When replacing a fuse, always use one with the specified rated capacity.
Note    
Using a fuse with a higher capacity than the specified one may cause damage to components or even a fire.
Inspection of Electrical System
1.
Be sure to turn the ignition switch "OFF" and disconnect the battery negative ( - ) cable before replacing or repairing electrical system parts.
Note    
Disconnecting the battery negative ( - ) cable during system check will clear the error code stored in the engine control module (ECM).
Read the fault code before disconnecting the battery negative ( - ) cable.

General Information — General Information / General Service Information illustration

2.
Fix the wiring with a clamp to prevent stretching.

General Information — General Information / General Service Information illustration

3.
If the wiring contact with the edge or end of the part, wrap the interference part with tape to protect it from damage.

General Information — General Information / General Service Information illustration

4.
When assembling vehicle parts, be careful not to damage the wiring.

General Information — General Information / General Service Information illustration

5.
Be careful not to throw or cause shock to relays, sensors, electrical parts.

General Information — General Information / General Service Information illustration

6.
ECMs and relays are easy to get damaged by overheating.
At temperatures above 176°F (80°C), disconnect electrical parts before inspection work.

General Information — General Information / General Service Information illustration

7.
Loose connector connection may cause failure, so make sure that the connector is properly connected.

General Information — General Information / General Service Information illustration

8.
When disconnecting the connector, hold the connector body.

General Information — General Information / General Service Information illustration

9.
When disconnecting the lockable connector, release the lock as shown below.

General Information — General Information / General Service Information illustration

10.
When installing the lockable connector, push it in until a "click" sound is herd.

General Information — General Information / General Service Information illustration

11.
When checking the energization or voltage of a connector terminal with a circuit tester, insert the probe from the harness side.
If the connector is a sealed type, be careful not to damage the insulation of the wiring, and insert the probe through the hole in the rubber sheath until the probe touches the terminal.

General Information — General Information / General Service Information illustration

12.
Select appropriate wiring as shown in the table below to prevent overloading the wiring.
Recommended
SAE Standard no.
Allowable current
Engine Room
The other parts
0.3mm²
AWG 22
-
5A
0.5mm²
AWG 20
7A
13A
0.85mm²
AWG 18
9A
17A
1.25mm²
AWG 16
12A
22A
2.0mm²
AWG 14
16A
30A
3.0mm²
AWG 12
22A
40A
5.0mm²
AWG 10
31A
54A

Other information:

Kia Seltos SP2 (2021-2026) Service Manual: Shift lock system

The automatic transmission in the Kia Seltos is equipped with a shift lock system. This safety feature helps prevent the transmission from being shifted from P (Park) into R (Reverse) unless the brake pedal is pressed. To shift the transmission from P (Park) into R (Reverse), follow these steps: Depress and hold the brake pedal. Start the engine or turn the ignition switch to the ON position.

Kia Seltos SP2 (2021-2026) Service Manual: Automatic transmission operation

The automatic transmission in the Kia Seltos provides 8 forward speeds and one reverse speed. The transmission selects each gear automatically according to the shift lever position, vehicle speed, engine load, and driving conditions. NOTICE The first several shifts on a new Kia Seltos, or after the battery has been disconnected, may feel slightly abrupt.