
Battery visual and basic inspection.
| 1. |
Check the battery terminal corrosion and connection.
|
| 2. |
Check the battery leakage or swelling.
|
| 3. |
Check the case for damage.
|
Alternator Charging Current Inspection
| 1. |
Check the alternator charging current.
G1.6 T-GDI GAMMA II
(Refer to Charging System - "Alternator")
G2.0 MPI NU
(Refer to Charging System - "Alternator")
|
Vehicle Parasitic Current Inspection
[Using an Ammeter]
| 1. |
Turn all electric devices OFF, and then turn the IG OFF.
|
| 2. |
Close all doors except the engine hood, and then lock all doors.
|
–
|
Disconnect the connector from the hood switch to prevent it from being operated.
|
|
| 3. |
Wait until the main system of the vehicle becomes sleep mode.
|
For an accurate measurement of a vehicle parasitic current, all electrical systems should go to
sleep mode. (It takes at least one hour or at most one day.) However, an approximate vehicle
parasitic current can be measured after 10 - 20 minutes.
|
|
| 4. |
Connect an ammeter between the battery negative ( - ) terminal and the negative ( - ) cable terminal, and
then disconnect the battery cable ( - ) terminal slowly.
|
•
|
Be careful not to let the lead wire of the ammeter come off the battery terminal and the
cable so that the battery is not initialized.
|
|
•
|
If the battery is initialized due to disconnection of lead wire of ammeter from the
battery cable or terminal, reconnect the battery and start the engine, or measure from the
first step after the IG is on for more than 10 seconds.
|
|
•
|
To prevent battery initialization in advance, follow the procedure below.
|
| 1) |
Connect the jumper cable between the battery ( - ) terminal and the cable ( - ) terminal
first.
|
| 2) |
Disconnect the negative ( - ) battery terminal.
|
| 3) |
Connect the ammeter in parallel to the jumper cable.
|
| 4) |
Disconnect the jumper cable and check the parasitic current value of the ammeter.
|
|

|
| 5. |
Check the parasitic current value of the ammeter.
|
•
|
If the parasitic current exceeds the limit value, remove the fuse one by one and measure it to
find the problem circuit.
|
|
•
|
Re-measure the parasitic current and find the problem unit by removing the units connected to the
problem circuit one by one.
|
Limit value (after 10 - 20 min.) : Below 50 mA
|
|
[[Using the Clamp Type Ammeter]
| 1. |
Turn all electric devices OFF, and then turn the IG OFF.
|
| 2. |
Close all doors except the engine hood, and then lock all doors.
|
–
|
Disconnect the connector from the hood switch to prevent it from being operated.
|
|
| 3. |
Wait until the main system of the vehicle becomes sleep mode.
|
For an accurate measurement of a vehicle parasitic current, all electrical systems should go to
sleep mode. (It takes at least one hour or at most one day.) However, an approximate vehicle
parasitic current can be measured after 10 - 20 minutes.
|
|
| 4. |
Install the clamp type ammeter on battery negative ( - ) cable.
|
•
|
When using a clamp type ammeter, use an ammeter that can measure mA. If not, it is
difficult to measure the correct parasitic current.
|
|
•
|
When ( - ) sign appears on the ammeter of the clamp type, install the ammeter in the
opposite direction.
|

|
|
| 5. |
Check the parasitic current value of the ammeter.
|
•
|
If the parasitic current exceeds the limit value, remove the fuse one by one and measure it to
find the problem circuit.
|
|
•
|
Re-measure the parasitic current and find the problem unit by removing the units connected to the
problem circuit one by one.
|
Limit value (after 10 - 20 min.) : Below 50 mA
|
|
Battery Performance Inspection
|
•
|
Check that the battery positive ( + ) and negative ( - ) terminals are properly connected.
|
|
•
|
Do not disconnect the battery while the engine is running.
|
|
| 1. |
Measure the performance of the battery by using the battery tester and battery load tester.
|
Battery Voltage Inspection
| 1. |
If it is within 20 minutes since the engine is stopped, turn on the ignition switch and operate the
electric devices (headlamp, blower motor, rear defogger) for 60 seconds to get rid of residual voltage.
|
| 3. |
Measure the voltage between the negative ( - ) terminal and battery positive ( + ) terminal of the
battery.
Specified voltage : approximately 12.5 - 12.9 V [20°C
(68°F)]
|
|
| 4. |
If the measured value is below the specified voltage, charge the battery.
|
AGM Battery Charging
| 1. |
Check the state of charge of the battery, and charge the battery if required.
How to charge IU or WU
IU or WU charging voltage : 14.7 V [20 - 30°C (68 - 86°F)] approximately 24 hours
Minimum charging voltage [20°C (68°F)] : 14.4 V
Maximum charging voltage [20°C (68°F)] : 14.8 V
A capacity of 10% of the charging current is recommended (e.g. 80 Ah : 100% = 8.0 A of charging
current)
|
|
|
•
|
Do not charge with a voltage of 15.2 V or higher.
|
|
•
|
Do not open or remove the cap on the top of the AGM battery.
|
|
•
|
Since explosive gas is formed in each cell when charging the battery, any actions that may cause
ignition such as fire, sparks, light rays, smoking, etc. during or immediately after charging the
battery are prohibited.
|
|
•
|
Do not open the circuit while the battery is charging as it will generate the spark, keep away
from nearby flammable material.
|
|
|
•
|
The temperature of the battery shall be maintained at approximately 20 - 30°C (68 - 86°F) during
the charging.
|
|
•
|
If the battery sensor is charged while connected to the battery, the sensor may not accurately
detect the state of the battery. Therefore, when the battery is fully charged, use it after about 10
hours (stabilizing time of the battery) at room temperature. Otherwise, it will result in a fault
code or the Alternator Management System (AMS) function may not work.
|
|
Other information:
Kia Seltos SP2 (2021-2026) Service Manual: Battery
The battery supplies electrical power for starting the engine and supports many electrical devices installed in the Kia Seltos. Keeping the battery in good condition helps ensure reliable starting and stable electrical system operation.
For best battery service
Keep the battery securely mounted.
Keep the top of the battery clean and dry.
Kia Seltos SP2 (2021-2026) Service Manual: Electronic Parking Brake (EPB) Description and Operation
Description
The Electric Parking Brake (EPB) is a parking brake system that operates the actuators of each caliper using an
electrical signal via button operation, unlike a parking brake operated by a lever or pedal.
The EPB has the function to engage the parking brake when the vehicle is stationary, to assist in braking in
emergencies due to brake failure, and to engage the parking brake automatically when the engine off.