Owner's library Kia Seltos Manuals Owner's manual pages, service notes, maintenance references and practical Kia Seltos help in one clean library.

Kia Seltos reference pages

Manuals, maintenance notes and quick owner help.

Find Kia Seltos operating instructions, warning light explanations, service information and owner guidance without digging through a full PDF.

Kia Seltos: Brake System / Brake System

Contents:

Repair Procedures

Operation and Leakage Check
Components
절 차
Brake booster (A)
Check brake operation by applying the brakes during a test drive. If the brakes do not work properly, check the brake booster. Replace the brake booster as an assembly if it does not work properly or if there are signs of leakage.
Piston cup and pressure cup inspection (B)
Check the brake operation by applying the brake.
Observe damage or oil leakage.
Replace the brake booster assembly if it is not operating properly or is damaged or leaking.
Check for a difference in brake pedal stroke between quick and slow brake applications. Replace the master cylinder if there is a difference in pedal stroke.
Brake hose (C)
Check for damage or leakage.
Look for damage or signs of fluid leakage. Replace the brake hose with a new one if it is damaged or leaking.
Caliper piston seal and piston boots (D)
Check brake operation by applying the brakes.and look for damage or signs of fluid leakage.
If the pedal does not work properly, the brakes drag, or there is damage or signs of fluid leakage, disassemble and inspect the brake caliper. Replace the boots and seals with new ones whenever the brake caliper is disassembled.

Brake System — Brake System / Repair Procedures / Operation and Leakage Check illustration

Brake Master Cylinder Components and Components Location

Component

Brake System — Brake System / Brake Master Cylinder / Components and Components Location / Component illustration

1. Reservoir cap
2. Reservoir
2-a. 1.0 - 1.5 N·m (0.10 - 0.15 kgf·m, 0.7 - 1.1 lb·ft, 8.7 - 13 lb·in)
3. Grommet
4. Master Cylinder
4-a. 9.8 - 15.7 N·m (1.0 - 1.6 kgf·m, 7.2 - 11.6 lb·ft)
5. Booster Assembly

Brake Master Cylinder Removal and Installation

Removal
Brake Reservoir Tank
1.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
2.
Disconnect the brake fluid level sensor connector (A) and separate the clip (B).

Brake System — Brake System / Brake Master Cylinder / Removal and Installation / Removal illustration

3.
Open the reservoir cap and then drain the brake fluid from the reservoir tank using tools like a brake fluid syringe.
Note    
Be careful not to spill brake fluid onto the vehicle or body. If brake fluid leaks, remove with a clean cloth as soon as possible.
Caution    
Make sure no dirt or other foreign matter is allowed to contaminate the brake fluid when opening the reservoir cap.
4.
Remove the screw, and then remove the reservoir tank (A).

Tightening torque :
1.0 - 1.5 N·m (0.10 - 0.15 kgf·m, 0.7 - 1.1 lb·ft)

Brake System — Brake System / Brake Master Cylinder / Removal and Installation / Removal illustration

Brake Master Cylinder and Reservoir Tank
1.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
2.
Open the reservoir cap and then drain the brake fluid from the reservoir tank using tools like a brake fluid syringe.
Note    
Be careful not to spill brake fluid onto the vehicle or body. If brake fluid leaks, remove with a clean cloth as soon as possible.
Caution    
Make sure no dirt or other foreign matter is allowed to contaminate the brake fluid when opening the reservoir cap.
3.
Separate the brake tubes (A) after loosening the flare nuts.

Tightening torque :
18.6 - 22.6 N·m (1.9 - 2.3 kgf·m, 13.7 - 16.6 lb·ft)

Brake System — Brake System / Brake Master Cylinder / Removal and Installation / Removal illustration

4.
Remove the brake master cylinder (B) after removing the nuts (A).

Tightening torque :
9.8 - 15.7 N·m (1.0 - 1.6 kgf·m, 7.2 - 11.6 lb·ft)

Brake System — Brake System / Brake Master Cylinder / Removal and Installation / Removal illustration

5.
Remove the reservoir tank (A) after removing the screw.

Tightening torque :
1.0 - 1.5 N·m (0.10 - 0.15 kgf·m, 0.7 - 1.1 lb·ft)

Brake System — Brake System / Brake Master Cylinder / Removal and Installation / Removal illustration

6.
Remove the reservoir grommet (A) and master cylinder O-ring (B).

Brake System — Brake System / Brake Master Cylinder / Removal and Installation / Removal illustration

Note    
Do not reuse the grommet and O-ring.
Installation
1.
Install in reverse order of removal.
Note    
•
Check the brake fluid level sensor is securely connected during installation, poor connection may cause the brake warning lamp to illuminate.
•
When installing the brake tube, make sure that the flare nuts is installed in the correct position.
2.
Fill the brake reservoir with brake fluid and perform the brake bleeding procedure.
(Refer to Brake System - "Brake Bleeding Procedures")
3.
Check brake fluid leakage and pedal operation.

Brake Booster Components and Components Location

Component

Brake System — Brake System / Brake Booster / Components and Components Location / Component illustration

1. Reservoir cap
2. Reservoir
2-a. 1.0 - 1.5 N·m (0.10 - 0.15 kgf·m, 0.7 - 1.1 lb·ft, 8.7 - 13 lb·in)
3. Grommet
4. Master Cylinder
4-a. 9.8 - 15.7 N·m (1.0 - 1.6 kgf·m, 7.2 - 11.6 lb·ft)
5. Booster Assembly

Brake Booster Troubleshooting

Brake booster operating test
1.
Run the engine for 1 to 2 minutes before stopping. It is normal for pedal strokes to gradually decrease as the pedal is pressed several times.
If the brake pedal stroke is constant, check the brake check valve, vacuum hose, brake booster.

Brake System — Brake System / Brake Booster / Troubleshooting / Brake booster operating test illustration

2.
Press the brake pedal with the engine stationary, and then start the engine. if the brake pedal moves downwards it is normal and abnormal if the brake pedal does not move.
3.
With the engine running, press the brake pedal and stop the engine. Hold the pedal pressed for 30 seconds. If the brake pedal height does not change, it is normal, and if the brake pedal height has risen, check the brake check valve, vacuum hose, and brake booster.

Brake System — Brake System / Brake Booster / Troubleshooting / Brake booster operating test illustration

Information    
If the brake booster meets all 3 steps above, the brake booster is OK. if even one step fails, check the check valve, vacuum hose, and brake booster.

Brake Booster Removal and Installation - G 1.6 MPI GAMMA

Removal and Installation
1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the engine control module (ECM).
(Refer to Engine Control / Fuel System - "Engine Control Module (ECM)")
3.
Disconnect the brake fluid level sensor connector (A) and wiring fastener (B).

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 MPI GAMMA / Removal and Installation illustration

4.
Separate the brake tube (A) from the master cylinder by loosening the tube flare nut.

Tightening torque :
18.6 - 22.6 N·m (1.9 - 2.3 kgf·m, 13.7 - 16.6 lb·ft)

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 MPI GAMMA / Removal and Installation illustration

5.
Remove the brake fluid from the master cylinder reservoir with a syringe.

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 MPI GAMMA / Removal and Installation illustration

Note    
Do not spill brake fluid on the vehicle as it may damage the paint. If brake fluid comes in contact with the paint, wash off immediately with water.
6.
Remove the master cylinder (B) from the brake booster after loosening the mounting nuts (A).

Tightening torque:
9.8 - 15.7 N·m (1.0 - 1.6 kgf·m, 7.2 - 11.6 lb·ft)

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 MPI GAMMA / Removal and Installation illustration

7.
Disconnect the vacuum sensor connector (A).

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 MPI GAMMA / Removal and Installation illustration

8.
Disconnect the brake vacuum hose (A).

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 MPI GAMMA / Removal and Installation illustration

9.
Remove the crash pad lower panel.
(Refer to Body - "Crash pad lower panel")
10.
Remove the snap pin (A) and clevis pin (B).

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 MPI GAMMA / Removal and Installation illustration

Note    
•
Before installing the pin, apply the grease to the joint pin.
•
Use a new snap pin whenever installing.
11.
Remove the brake booster mounting nuts (A).

Tightening torque :
16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 MPI GAMMA / Removal and Installation illustration

12.
Remove the brake booster (A).

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 MPI GAMMA / Removal and Installation illustration

13.
Install in the reverse order of removal.
14.
After installation, bleed the brake system.
(Refer to Brake system - "Brake Bleeding Procedures")

Brake Booster Removal and Installation - G 1.6 T-GDI GAMMA ll

Removal
Caution    
Since there is a risk of injury due to high pressure fuel leakage, do not perform any work right after the engine is stopped.
Note    
Some residual fuel may be released, so cover the connection with a cloth or the like before disconnecting the fuel line.
1.
Remove the engine room under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
2.
Release the residual pressure in fuel line.
(Refer to Fuel Delivery System - "Release Residual Pressure in Fuel Line")
3.
Remove the brake master cylinder.
(Refer to Brake System - "Brake Master Cylinder")
4.
Separate the vapor tube (A).

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 T-GDI GAMMA ll / Removal illustration

5.
Separate the low pressure fuel feed tube (A).

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 T-GDI GAMMA ll / Removal illustration

Note    
•
Cover the connection with a clean cloth since the residual fuel may be released after "Release Residual Pressure in Fuel Line" procedures.
•
When separating the fuel supply tube, separate it after pressing the holder (A) firmly by using the clip remover.

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 T-GDI GAMMA ll / Removal illustration

6.
Separate the fuel lines (A) after separating the holders (B) from the brackets.

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 T-GDI GAMMA ll / Removal illustration

7.
Release the clamp, and then disconnect the brake vacuum hose (A).

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 T-GDI GAMMA ll / Removal illustration

8.
Separate the brake pedal arm clevis pin (A) and the split pin (B).

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 T-GDI GAMMA ll / Removal illustration

Note    
Do not reuse the split pin.
9.
Remove the brake member assembly nuts (A).

Tightening torque :
16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 T-GDI GAMMA ll / Removal illustration

10.
Support the automatic transaxle by using a tool such as a garage jack (A).

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 T-GDI GAMMA ll / Removal illustration

11.
Remove the automatic transaxle mounting bracket bolts (A).

Tightening torque :
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 T-GDI GAMMA ll / Removal illustration

12.
Down the automatic transaxle (A) by lowering the jack.

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 T-GDI GAMMA ll / Removal illustration

Note    
Excessive lowering of the automatic transmission (A) may damage the engine mounting.
13.
Remove the brake booster (A).

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 T-GDI GAMMA ll / Removal illustration

Note    
Be careful not to damage any surrounding parts when removing or installing the brake booster (A).
Installation
1.
Install in reverse order of removal.
Note    
•
Be careful not to twist the brake vacuum hose when installing.
•
Apply the grease when installing the brake pedal arm clevis pin (Grease type : GREASE PDLV-1)
•
Be careful not to change the mounting position of the clevis pin and split pin.
Information    
To minimize damage to the thread and brake member assembly during installation, tighten all nuts with hands and then tighten them to the tightening torque values in the order shown below.

Brake System — Brake System / Brake Booster / Removal and Installation - G 1.6 T-GDI GAMMA ll / Installation illustration

2.
Fill the brake reservoir with brake fluid and perform the brake bleeding procedure.
(Refer to Brake System - "Brake Bleeding Procedures")
3.
Check the brake fluid leakage and pedal operating condition.

Brake Booster Removal and Installation - G 2.0 MPI NU

Removal
1.
Remove the brake master cylinder.
(Refer to Brake System - "Brake Master Cylinder")
2.
Release the clamp, and then disconnect the brake vacuum hose (A).

Brake System — Brake System / Brake Booster / Removal and Installation - G 2.0 MPI NU / Removal illustration

3.
Remove the brake pedal arm mounting clevis pin (A) and split pin (B).

Brake System — Brake System / Brake Booster / Removal and Installation - G 2.0 MPI NU / Removal illustration

Note    
Do not reuse the split pin.
4.
Remove the brake member assembly nuts (A).

Tightening torque :
16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)

Brake System — Brake System / Brake Booster / Removal and Installation - G 2.0 MPI NU / Removal illustration

5.
Remove the brake booster (A).

Brake System — Brake System / Brake Booster / Removal and Installation - G 2.0 MPI NU / Removal illustration

Note    
Be careful not to damage any surrounding parts when removing or installing the brake booster (A).
Installation
1.
Install in reverse order of removal.
Note    
•
Be careful not to twist the brake vacuum hose when installing.
•
Apply the grease when installing the brake pedal arm clevis pin (Grease type : GREASE PDLV-1)
•
Be careful not to change the mounting position of the clevis pin and split pin.
Information    
To minimize damage to the thread and brake member assembly during installation, tighten all nuts with hands and then tighten them to the tightening torque values in the order shown below.

Brake System — Brake System / Brake Booster / Removal and Installation - G 2.0 MPI NU / Installation illustration

2.
Fill the brake reservoir with brake fluid and perform the brake bleeding procedure.
(Refer to Brake System - "Brake Bleeding Procedures")
3.
Check the brake fluid leakage and pedal operating condition.

Brake Booster Inspection

Inspection
1.
Check the check valve inside the vacuum hose.
Note    
Do not disassemble the check valve from the vacuum hose.
2.
Check the boots for damage.

Brake Line Components and Components Location

Component

Brake System — Brake System / Brake Line / Components and Components Location / Component illustration

1. HECU Flare nut 13.7 - 16.7 N·m (1.4 - 1.7 kgf·m, 10.1 - 12.3 lb·ft)
2. HECU and master cylinder flare nut 18.6 - 22.6 N·m (1.9 - 2.3 kgf·m, 13.7 - 16.6 lb·ft)
3. HECU bracket and body mounting bolt 19.6 - 29.4 N·m (2.0 - 3.0 kgf·m, 14.5 - 21.7 lb·ft)
4. Master cylinder and HECU flare nut 18.6 - 22.6 N·m (1.9 - 2.3 kgf·m, 13.7 - 16.6 lb·ft)
5. Brake line tube flare nut 13.7 - 16.7 N·m (1.4 - 1.7 kgf·m, 10.1 - 12.3 lb·ft)
6. Front caliper and brake hose bolt 24.5 - 29.4 N·m (2.5 - 3.0 kgf·m, 18.1 - 21.7 lb·ft)
7. Front brake line tube flare nut 13.7 - 16.7 N·m (1.4 - 1.7 kgf·m, 10.1 - 12.3 lb·ft)
8. Rear caliper and brake hose bolt 24.5 - 29.4 N·m (2.5 - 3.0 kgf·m, 18.1 - 21.7 lb·ft)
9. Rear brake line tube flare nut 13.7 - 16.7 N·m (1.4 - 1.7 kgf·m, 10.1 - 12.3 lb·ft)

Brake Line Removal and Installation

Removal
Front brake line
1.
Disconnect the battery negative ( - ) terminal.
2.
Disconnect the brake fluid level sensor connector (A) and separate the clip (B).

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

3.
Open the reservoir cap and then drain the brake fluid from the reservoir tank using tools like a brake fluid syringe.
Note    
Be careful not to spill brake fluid onto the vehicle or body. If brake fluid leaks, remove with a clean cloth as soon as possible.
Caution    
Make sure no dirt or other foreign matter is allowed to contaminate the brake fluid when opening the reservoir cap.
4.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
5.
Remove the brake line bracket after removing the bolt (A).

Tightening torque :
8.8 - 13.7 N·m (0.9 - 1.4 kgf·m, 6.5 - 10.1 lb·ft)

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

6.
Remove the brake hose clip (B), and then separate the brake tube after loosening the tube flare nut (A).

Tightening torque :
13.7 - 16.7 N·m (1.4 - 1.7 kgf·m, 10.1 - 12.3 lb·ft)

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

7.
Remove the brake hose (B) after removing the bolt (A).

Tightening torque:
24.5 - 29.4 N·m (2.5 - 3.0 kgf·m, 18.1 - 21.7 lb·ft)

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

Note    
Do not reuse the washer (B) when installing the brake hose.
Rear Brake Line
1.
Disconnect the battery negative ( - ) terminal.
2.
Disconnect the brake fluid level sensor connector (A) and separate the clip (B).

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

3.
Open the reservoir cap and then drain the brake fluid from the reservoir tank using tools like a brake fluid syringe.
Note    
Be careful not to spill brake fluid onto the vehicle or body. If brake fluid leaks, remove with a clean cloth as soon as possible.
Caution    
Make sure no dirt or other foreign matter is allowed to contaminate the brake fluid when opening the reservoir cap.
4.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
5.
Remove the brake hose clip (B), and then separate the brake tube after loosening the tube flare nut (A).

Tightening torque :
13.7 - 16.7 N·m (1.4 - 1.7 kgf·m, 10.1 - 12.3 lb·ft)

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

6.
Remove the brake hose (B) after removing the bolt (A).

Tightening torque :
24.5 - 29.4 N·m (2.5 - 3.0 kgf·m, 18.1 - 21.7 lb·ft)

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

Note    
Do not reuse the washer (B) when installing the brake hose.
Installation
1.
Install in reverse order of removal.
Note    
Check brake fluid level sensor connector (A) is securely installed. Incorrect installation may cause the brake warning lamp to illuminate.
2.
Fill the brake reservoir with brake fluid and perform air bleeding.
(Refer to Brake System - "Brake Bleeding Procedures")

Brake Line Inspection

Inspection
1.
Check the brake tube and hose for crack or corrosion.
2.
Check the tube flare nuts for damage.

Brake Pedal Components and Components Location

Component

Brake System — Brake System / Brake Pedal / Components and Components Location / Component illustration

1. Brake Member Assembly
1-a. 16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)
1-b. 16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)
2. Stop Lamp Switch
3. Return spring
4. Brake Pedal Arm
4-a. 24.5 - 34.3 N·m (2.5 - 3.5 kgf·m, 18.1 - 25.3 lb·ft)
5. Brake Pedal Pad
6. Pedal Stopper
7. Brake Pedal Arm Bushing

Brake Pedal Removal and Installation

Removal
1.
Disconnect the battery negative ( - ) terminal.
2.
Remove the crash pad lower panel.
(Refer to Body - "Crash Pad Lower Panel")
3.
Disconnect the stop lamp switch connector (A).

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

4.
Remove the stop lamp switch connector wiring fastener (A).

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

5.
Separate the universal joint assembly (A) from the MDPS column and housing after removing the bolt.

Tightening torque :
49.0 - 52 N·m (5.0 - 5.3 kgf·m, 36.2 - 38.3 lb·ft)

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

Note    
Do not reuse the universal joint assembly bolt.
6.
Separate the brake pedal arm clevis pin (A) and the split pin (B).

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

Note    
Do not reuse the split pin.
7.
Remove the brake pedal member assembly nuts (A).

Tightening torque :
16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

8.
Remove the brake pedal assembly after removing the nut (A),

Tightening torque :
16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.
Note    
•
Apply the grease when installing the brake pedal arm clevis pin (Grease type : GREASE PDLV-1)
•
Be careful not to change the mounting position of the clevis pin and split pin.
Information    
To minimize damage to the thread and brake member assembly during installation, tighten all nuts with hands and then tighten them to the tightening torque values in the order shown below.

Brake System — Brake System / Brake Pedal / Removal and Installation / Installation illustration

2.
Check the brake pedal operating normally after installation.
3.
Check brake fluid leakage and pedal operation.

Brake Pedal Inspection

Inspection
1.
Check if the brake pedal is damaged.
2.
Check if the relevant parts are cracked, or damaged.
3.
Inspect the stop lamp switch.
(Refer to Brake System - "Stop Lamp Switch")

Stop Lamp Switch Components and Components Location

Component

Brake System — Brake System / Stop Lamp Switch / Components and Components Location / Component illustration

1. Brake Member Assembly
1-a. 16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)
1-b. 16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)
2. Stop Lamp Switch
3. Return spring
4. Brake Pedal Arm
4-a. 24.5 - 34.3 N·m (2.5 - 3.5 kgf·m, 18.1 - 25.3 lb·ft)
5. Brake Pedal Pad
6. Pedal Stopper
7. Brake Pedal Arm Bushing

Stop Lamp Switch On Vehicle Inspection

On Vehicle Inspection
1.
The brake system can be more quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
(1)
Self diagnosis : Inspection and display fault code (DTC)
(Refer to DTC guide when fault code is found.)
Information    
Refer to the KDS screen for operating conditions and details.

Stop Lamp Switch Description and Operation

Description and Operation

Brake System — Brake System / Stop Lamp Switch / Description and Operation illustration

Operation principle of inductive non-contact switch
1.
Use the high-frequency magnetic field and the induced current that is generated by oscillation (to approved voltage) of the coil in the switch.
2.
The eddy current is generated on surface of metal by self inductance effect if there is metal in high frequency magnetic field.
3.
The eddy current that is generated decreases the high frequency magnetic field as much as amount of generated by disturbing the switch's magnetic flux.
4.
ON-OFF by determining whether high voltage magnetic field is decreases or not(calculate the voltage difference by length between metal and coil).

Stop Lamp Switch Circuit Diagram

Schematic Diagram

Brake System — Brake System / Stop Lamp Switch / Circuit Diagram / Schematic Diagram illustration

Circuit Diagram

Brake System — Brake System / Stop Lamp Switch / Circuit Diagram illustration

Stop Lamp Switch Troubleshooting

Troubleshooting
1.
Part diagnosis
Name
Suspected Cause
Symptom
Correction Method
Switch fuse
Faulty fuse connection, Damaged fuse
–
DTC code : (Refer to "DTC guide")
–
Shifting gear trouble, Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble, Stop lamp lighting trouble, ESC OFF light illuminated.
Brake System — Brake System / Stop Lamp Switch / Troubleshooting illustration A waveform inspection is performed using an oscilloscope on each part during vehicle acceleration/braking. (Refer to stop lamp switch circuit inspection procedures)

Brake System — Brake System / Stop Lamp Switch / Troubleshooting illustration Refer to the relevant repair procedures of the part when something abnormal is discovered in the waveform (Refer to the repair procedures of the relevant part and if necessary replace it)
Relay fuse
Faulty fuse connection, Damaged fuse
–
DTC code : (Refer to "DTC guide")
–
Shifting gear trouble, Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble, Stop lamp lighting trouble, ESC OFF light illuminated.
Stop lamp switch
•
Damaged wiring of each part
•
Faulty connection to connector
•
Each part is defective
–
DTC code : (Refer to "DTC guide")
–
Shifting gear trouble, Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble, Stop lamp lighting trouble , ESC OFF light illuminated.
Stop signal electronic module (If it applies)
–
DTC code : (Refer to "DTC guide")
–
Symptom : Shifting gear trouble, Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble, Stop lamp lighting trouble , ESC OFF light illuminated.
Engine Control Module
(ECM)
–
DTC code : (Refer to "DTC guide")
–
Symptom :Shifting gear trouble,Cruise control function cancelation trouble
Integrated Body Control Unit (IBU)
–
Shifting gear trouble
Inhibitor Switch
–
DTC code : (Refer to "DTC guide")
–
Symptom : Shifting gear trouble, Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble
Smart Key Unit (SMK)
–
Faulty engine start
Electronic Parking Brake(EPB)
–
Electronic Parking Brake (EPB)
ABS/ESC control module
(Pressure sensor)
–
ESC OFF light illuminated.

2.
Symptom diagnosis
Symptom
Suspected Causes
Correction Method
Faulty engine start
Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, ABS/ESC control module, Each wire, Connector
Brake System — Brake System / Stop Lamp Switch / Troubleshooting illustration Inspect waveform using an oscilloscope on each part during vehicle acceleration/braking. (Refer to stop lamp switch circuit inspection Procedures)

Brake System — Brake System / Stop Lamp Switch / Troubleshooting illustration Refer to the relevant repair procedures of the part when something abnormal is discovered in the waveform (Refer to the repair procedures of the relevant part and if necessary replace it)
Shifting gear trouble
Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, IBU, ECM, Inhibitor switch, Each wire, Connector
ESC OFF light illuminated
Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, ABS/ESC control module, Each wire, Connector
P0504
Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, ECM, Each wire, Connector
Stop lamp not working
Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, ECM, Each wire, Connector
Stop lamp always on
Stop lamp switch, Stop signal electronic module, Wiring short circuit, Damaged fuse

3.
Refer to DTC guide when the related DTC codes are displayed.

Stop Lamp Switch Replacement

Replacement
1.
Disconnect the battery negative ( - ) terminal.
2.
Remove the crash pad lower panel.
(Refer to Body - "Crash Pad Panel")
3.
Disconnect the stop lamp switch connector (A).

Brake System — Brake System / Stop Lamp Switch / Replacement illustration

4.
Pull the locking plate (A) in the direction of the arrow.

Brake System — Brake System / Stop Lamp Switch / Replacement illustration

5.
Turn the stop lamp switch (A) counterclockwise about 45 degrees and remove it.

Brake System — Brake System / Stop Lamp Switch / Replacement illustration

6.
A confirmation can be made to see if the connector has been secured properly and if a connection mark is present.

Brake System — Brake System / Stop Lamp Switch / Replacement illustration

7.
Insert the stop lamp switch (A) until the contact part is invisible, and rotate it clockwise at 45° to install it to the brake pedal.

Brake System — Brake System / Stop Lamp Switch / Replacement illustration

8.
Push the locking plate (A) in the direction of the arrow to install it.

Brake System — Brake System / Stop Lamp Switch / Replacement illustration

9.
Check the gap (A) between the stop lamp switch and the brake pedal stopper.

Stop lamp switch clearance (A) :
1.0 - 2.0 mm (0.03 - 0.07 in.)

Brake System — Brake System / Stop Lamp Switch / Replacement illustration

10.
Connect the stop lamp switch connector (A).

Brake System — Brake System / Stop Lamp Switch / Replacement illustration

Note    
If the stop lamp switch gap is outside 1.0 - 2.0 mm (0.03 - 0.07 in.), reinstall the stop lamp switch.
11.
Install the crash pad lower panel.
(Refer to Body - "Crash Pad Panel")

Stop Lamp Switch Adjustment

Adjustment
Adjusting stop lamp switch clearance.
1.
Turn the IG OFF and disconnect the battery negative ( - ) terminal.
2.
Remove the crash pad lower panel.
(Refer to Body - "Crash Pad Panel")
3.
Check the stop lamp switch gap.

Stop lamp switch gap (A) : 1.0 - 2.0 mm (0.04 - 0.08 in.)

Brake System — Brake System / Stop Lamp Switch / Adjustment illustration

4.
If the clearance exceeds the limit, remove the stop lamp switch and check for damage to surrounding parts such as clips.
5.
If it is normal, reinstall the stop lamp switch and check the gap.

Front Brake Caliper Components and Components Location

Component

Brake System — Brake System / Front Brake Caliper / Components and Components Location / Component illustration

1. Brake Caliper Body
1-a. 21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)
2. Air Bleed Screw
2-a. 6.9 - 12.7 N·m (0.7 - 1.3 kgf·m, 5.1 - 9.4 lb·ft)
3. Torque member
3-a. 78.5 - 98.1 N·m (8.0 - 10.0 kgf·m, 57.9 - 72.3 lb·ft)
4. Brake pad
5. Brake Pad Liner
6. Brake Pad Return Spring




Front Brake Caliper Removal and Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Piston expander
09581 - 11000

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Special Service Tool illustration

Spreading the front brake caliper piston.

Removal
1.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Separate the front brake hose after removing the bolt (A).

Tightening torque :
24.5 - 29.4 N·m (2.5 - 3.0 kgf·m, 18.1 - 21.7 lb·ft)

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Removal illustration

Note    
Do not reuse the washers (A) when installing the brake hose.

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Removal illustration

3.
Remove the front brake caliper body after removing the bolts (A).

Tightening torque :
21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Removal illustration

4.
Remove the brake pad return springs (A).

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Removal illustration

5.
Remove the brake pads (A).

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Removal illustration

6.
Remove the brake torque member and pad retainers (B) after removing the bolts and washers (A).

Tightening torque :
78.5 - 98.1 N·m (8.0 - 10.0 kgf·m, 57.9 - 72.3 lb·ft)

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Removal illustration

Note    
Do not reuse the torque member mounting bolts.
Installation
1.
Install in reverse order of removal.
Note    
•
Be careful not to damage the piston when pressing it.
•
Be careful not to touch the piston when installing the caliper body to the torque member.
•
Press the brake piston using SST (09581 - 11000) when installing the caliper body.

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Installation illustration

2.
Fill the brake reservoir with brake fluid and perform air bleeding.
(Refer to Brake System - "Brake Bleeding Procedures")
3.
Check the brake fluid leakage and pedal operating condition.
4.
Depress the brake pedal several times to ensure that the brake pads are correctly positioned, then check operation.

Front Brake Disc Components and Components Location

Component

Brake System — Brake System / Front Brake Disc / Components and Components Location / Component illustration

1. Front Brake Disc
1-a. 4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in)

Front Brake Disc On Vehicle Inspection

On Vehicle Inspection
Disc Cleaning before Inspection
The rust caused by leaving the vehicle unattended for a long period of time is naturally removed under normal driving conditions. It may affect thickness and runout measurements, please remove rust on the brake disc for accurate measurements.
1.
Check the brake disc for rust.
2.
Spray the cleaning solution on rusted surface of disc.

Cleaning solution : Water (300 ml) + Detergent (15 ml)

Warning    
Do not use lubricating, oil-based cleaning agents (wax, rust inhibitors). Poor braking performance and risk of fire due to pad friction during braking.
3.
Drive the vehicle up to 30 MPH and depress the brake up to stop for complete repeat more than 5 cycles.
4.
Clean the brake disc with clean water.
5.
Check the brake disc for rust.
6.
If rust is not removed, repeat the above procedure again.
Front Brake Disc Thickness Check
1.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Check the brake disc for damage.
3.
Measure the brake disc thickness (A) and run-out using the micro meter and dial gauge at least 24 locations on the same column along the lines shown in the figure below.

Brake System — Brake System / Front Brake Disc / On Vehicle Inspection illustration


Front Brake Disc Thicknes
Standard
for 15 inch wheel disc : 23.0 mm (0.90 in.)
for 16 in wheel disc : 25.0 mm (0.98 in.)
Service Limit
for 15 inch wheel disc : 21.4 mm (0.84 in.)
for 16 inch disc : 23.4 mm (0.92 in.)
DTV (Disc Thickness Variation) :
0.015 mm (0.0005 in.) [Circumference, Radial direction]

4.
If the thickness difference between each measuring part is greater than standard, resurface or replace the brake disc.
Note    
•
Resurface the brake disc according to the method of using the equipment in possession.
•
If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
5.
Install the front wheel and tires.
(Refer to Suspension System - "Wheel")
Front Brake Disc Runout Inspection
1.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Install the dial gauge perpendicular to the brake disc's external diameter of 10 mm (0.40 in.) and rotate the disc to measure the run-out.

Brake Disc Run Out
Service Limit : 0.050 mm (0.0019 in.)

Brake System — Brake System / Front Brake Disc / On Vehicle Inspection illustration

3.
If the brake disc run-out exceeds the limit, resurface or replace the brake disc.
Note    
•
Resurface the brake disc according to the method of using the equipment in possession.
•
If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
4.
Install the front wheel and tires.
(Refer to Suspension System - "Wheel")

Front Brake Disc Removal and Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Piston expander
09581 - 11000

Brake System — Brake System / Front Brake Disc / Removal and Installation / Special Service Tool illustration

Spreading the front brake caliper piston.

Removal
1.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Remove the guide rod lower bolt (A) and then open the caliper body (B).

Tightening torque :
21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

3.
Remove the return springs (A).

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

4.
Remove the brake pads (A).

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

5.
Remove the caliper assembly (B) after removing the caliper carrier bolts (A).

Tightening torque :
78.5 - 98.1 N·m (8.0 - 10.0 kgf·m, 57.9 - 72.3 lb·ft)

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

Note    
Secure the removed brake caliper body using a tool such as a cable tie.
6.
Remove the front brake disc (A) after removing the screws.

Tightening torque :
4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft)

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.
Note    
•
Be careful not to damage the piston when pressing it.
•
Be careful not to interfere with the piston when assembling the caliper body to the carrier.
•
Press the brake piston using SST (09581 - 11000) when installing the caliper body.

Brake System — Brake System / Front Brake Disc / Removal and Installation / Installation illustration

2.
Depress the brake pedal several times to ensure that the brake pads are correctly positioned, then check operation.

Rear Brake Caliper Components and Components Location

Component
Rear Caliper (EPB)

Brake System — Brake System / Rear Brake Caliper / Components and Components Location / Component illustration

1. EPB actuator
1-a. 7.8 - 10.8 N·m (0.8 - 1.1 kgf·m, 5.8 - 8.0 lb·ft)
2. Air Bleed Screw
2-a. 6.9 - 12.7 N·m (0.7 - 1.3 kgf·m, 5.1 - 9.4 lb·ft)
3. Brake Caliper Body
3-a. 21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)
4. Torque Member
4-a. 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)
5. Brake Pad
6. Brake Pad Liner

Rear Caliper (None EPB)

Brake System — Brake System / Rear Brake Caliper / Components and Components Location / Component illustration

1. Parking Brake Cable Lever
6. Caliper Piston
1-a. 24.5 - 34.3 N·m (2.5 - 3.5 kgf·m, 18.1 - 25.3 lb·ft)
7. Piston Seal
2. Parking Brake Cable Guide
8. Piston Boot
3. Parking Brake Cable Return Spring
9. Torque Member
4. Air Bleed Screw Cap
9-a. 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft
5. Rear Caliper Body
10. Brake Pad
5-a. 21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)
11. Brake Pad Return Spring
5-b. 6.9 - 12.7 N·m (0.7 - 1.3 kgf·m, 5.1 - 9.4 lb·ft)
12. Brake Pad Liner

Rear Brake Caliper Removal and Installation

Removal and Installation
1.
Release the parking brake.
• EPB : Release the parking brake by using the KDS.
(Refer to Brake System - "Electronic Parking Brake (EPB)")
• None EPB : Release the hand lever parking brake fully.
2.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
3.
Disconnect the EPB actuator connector or parking brake cable.
• EPB : Disconnect the EPB actuator connector (A).

Brake System — Brake System / Rear Brake Caliper / Removal and Installation illustration

• None EPB : Remove the clip (A), and then separate the parking brake cable (B).
[2WD]

Brake System — Brake System / Rear Brake Caliper / Removal and Installation illustration

[4WD]

Brake System — Brake System / Rear Brake Caliper / Removal and Installation illustration

4.
Separate the brake hose from the brake caliper after removing the brake hose bolt (A).

Tightening torque :
24.5 - 29.4 N·m (2.5 - 3.0 kgf·m, 18.1 - 21.7 lb·ft)

Brake System — Brake System / Rear Brake Caliper / Removal and Installation illustration

Note    
Do not reuse the washers (A) when installing the brake hose.

Brake System — Brake System / Rear Brake Caliper / Removal and Installation illustration

5.
Remove the caliper body (B) after removing the guide rod bolt (A).

Tightening torque :
21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Brake System — Brake System / Rear Brake Caliper / Removal and Installation illustration

6.
Remove the brake pads (A).

Brake System — Brake System / Rear Brake Caliper / Removal and Installation illustration

7.
Remove the caliper carrier (B) after removing the bolts (A).

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Brake System — Brake System / Rear Brake Caliper / Removal and Installation illustration

Note    
Do not reuse the caliper carrier bolts.
Installation
1.
Install in reverse order of removal.
Note    
•
Be careful not to interfere with the piston when assembling the caliper body to the carrier.
•
When installing the caliper body, turn the brake piston clockwise using a tool such as the long nose pliers (A) to press it in.

Brake System — Brake System / Rear Brake Caliper / Removal and Installation / Installation illustration

•
Check the piston groove position before installing the caliper body.

Brake System — Brake System / Rear Brake Caliper / Removal and Installation / Installation illustration

2.
Fill the brake reservoir with brake fluid and perform air bleeding.
(Refer to Brake System - "Brake Bleeding Procedures")
3.
After installation, adjust the parking brake according to the parking brake specification.
•
EPB - (Refer to Parking Brake System - "Electronic Parking Brake (EPB)")
•
None EPB - (Refer to Parking Brake System - "Parking Brake Lever")
4.
Depress the brake pedal several times to ensure that the brake pads are correctly positioned, then check operation.
5.
Check the brake fluid leakage and pedal operating condition.
6.
Check if the parking brake is operating normally.

Rear Brake Caliper Replacement

Replacement
Rear Caliper Piston Boot and Seal
Note    
Do not reuse the piston boot and seal.
1.
Put the clean cloth (A) between the caliper body and piston.

Brake System — Brake System / Rear Brake Caliper / Replacement illustration

2.
Inject compressed air (A) inside the caliper to depress the piston.

Brake System — Brake System / Rear Brake Caliper / Replacement illustration

Caution    
Be careful fingers or hands crush hazard when depressing the piston.
3.
Remove the caliper piston (A).

Brake System — Brake System / Rear Brake Caliper / Replacement illustration

Note    
Be careful not to damage the caliper piston and the inside of the cylinder.
4.
Remove the caliper piston boot (A).

Brake System — Brake System / Rear Brake Caliper / Replacement illustration

5.
Remove the piston seal (A) using a screwdriver or a remover.

Brake System — Brake System / Rear Brake Caliper / Replacement illustration

Brake System — Brake System / Rear Brake Caliper / Replacement illustration

Note    
When using the tools, be careful not to damage the cylinder wall and piston seal groove.
6.
Clean the inside of the caliper cylinder and the piston.
7.
Insert the piston seal (B) to the cylinder seal groove (A).

Brake System — Brake System / Rear Brake Caliper / Replacement illustration

Note    
•
Do not reuse the caliper piston seal.
•
Apply assembling oil on the piston seal (0.1 - 0.4 cc)
•
Be careful not to let foreign matter enter the cylinder.
•
Check that there are no dents or poor assembly of the piston seal.
8.
Insert the piston boot (A) in the direction of the arrow to the edge of the piston.

Brake System — Brake System / Rear Brake Caliper / Replacement illustration

Note    
•
Do not reuse the piston boot.
•
Apply assembling oil on the piston boot.
•
Be careful not to damage the piston boot.
•
Be careful not to change the direction of the piston boot.
9.
Turn the spindle nut (A) clockwise and push it all the way in, and check the position (B) of the spindle.

Brake System — Brake System / Rear Brake Caliper / Replacement illustration

10.
Insert the piston boot (B) into the caliper cylinder groove (A).

Brake System — Brake System / Rear Brake Caliper / Replacement illustration

Note    
Be careful not to let foreign matter enter the cylinder.
11.
Check the position (A) of the caliper piston groove and insert it into the cylinder.

Brake System — Brake System / Rear Brake Caliper / Replacement illustration

Note    
•
When inserting the piston, be careful not to tilt the piston.
•
Be careful not to apply excessive force when inserting the piston.
•
Insert it slowly to prevent damage to the inside of the cylinder.
12.
Insert the piston all the way in, and check the caliper piston boot (A) is installed properly.

Brake System — Brake System / Rear Brake Caliper / Replacement illustration

13.
Install the caliper body.
14.
Fill the brake fluid to the 'MAX' line, and perform the brake bleeding procedures.
(Refer to Brake System - "Brake Bleeding Procedures")
15.
Depress the brake pedal several times to check that the brake fluid is not leaking.
16.
Check that the parking brake is operating normally.

Rear Brake Disc Components and Components Location

Component

Brake System — Brake System / Rear Brake Disc / Components and Components Location / Component illustration

1. Rear Brake Disc
1-a. 4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in)

Rear Brake Disc On Vehicle Inspection

On Vehicle Inspection
Disc Cleaning before Inspection
The rust caused by leaving the vehicle unattended for a long period of time is naturally removed under normal driving conditions. It may affect thickness and runout measurements, please remove rust on the brake disc for accurate measurements.
1.
Check the brake disc for rust.
2.
Spray the cleaning solution on rusted surface of disc.

Cleaning solution : Water (300 ml) + Detergent (15 ml)

Warning    
Do not use lubricating, oil-based cleaning agents (wax, rust inhibitors). Poor braking performance and risk of fire due to pad friction during braking.
3.
Drive the vehicle up to 30 MPH and depress the brake up to stop for complete repeat more than 5 cycles.
4.
Clean the brake disc with clean water.
5.
Check the brake disc for rust.
6.
If rust is not removed, repeat the above procedure again.
Rear Brake Thickness Check
1.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Check the brake disc for damage.
3.
Measure the brake disc thickness (A) and run out using a micrometer and dial gauge. Measure it at least 24 points.

Rear brake disc thickness (A)
Standard :
10.0 mm (0.39 in.)
Service limit :
8.4 mm (0.33 in.)
DTV (Disc Thickness Variation :
Less than 0.015 mm (0.0006 in.) [Circumference direction]
Less than 0.015 mm (0.0006 in.) [Radial direction]

Brake System — Brake System / Rear Brake Disc / On Vehicle Inspection illustration

4.
If the thickness difference between each measuring part is greater than standard, resurface or replace the brake disc.
Note    
•
Resurface the brake disc according to the method of using the equipment in possession.
•
If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
5.
Install the rear wheel and tires.
(Refer to Suspension System - "Wheel")
Rear Brake Disc Runout Inspection
1.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Install the dial gauge perpendicular to the brake disc's external diameter of 10 mm (0.40 in.) and rotate the disc to measure the run-out.

Brake Disc Run Out
Service limit : 0.055 mm (0.002 in.) or less.

Brake System — Brake System / Rear Brake Disc / On Vehicle Inspection illustration

3.
If the brake disc run-out exceeds the limit, resurface or replace the brake disc.
Note    
•
Resurface the brake disc according to the method of using the equipment in possession.
•
If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
4.
Install the rear wheel and tires.
(Refer to Suspension System - "Wheel")

Rear Brake Disc Removal and Installation

Removal and Installation
1.
Release the parking brake.
• EPB : Release the parking brake by using the KDS.
(Refer to Brake System - "Electronic Parking Brake (EPB)")
• None EPB : Release the hand lever parking brake fully.
2.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
3.
Disconnect the EPB actuator connector or parking brake cable.
• EPB : Disconnect the EPB actuator connector (A).

Brake System — Brake System / Rear Brake Disc / Removal and Installation illustration

• None EPB : Remove the clip (A), and then separate the parking brake cable (B).
[2WD]

Brake System — Brake System / Rear Brake Disc / Removal and Installation illustration

[4WD]

Brake System — Brake System / Rear Brake Disc / Removal and Installation illustration

4.
Remove the caliper body (B) after removing the guide rod bolt (A).

Tightening torque :
21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Brake System — Brake System / Rear Brake Disc / Removal and Installation illustration

Note    
Secure the removed brake caliper body using a tool such as a cable tie.
5.
Remove the brake pads (A).

Brake System — Brake System / Rear Brake Disc / Removal and Installation illustration

6.
Remove the caliper carrier (B) after removing the bolts (A).

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Brake System — Brake System / Rear Brake Disc / Removal and Installation illustration

Note    
Do not reuse the caliper carrier bolts.
7.
Remove the rear brake disc (A) after removing the screws.

Tightening torque :
4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft)

Brake System — Brake System / Rear Brake Disc / Removal and Installation illustration

Installation
1.
Install in reverse order of removal.
Note    
•
Be careful not to interfere with the piston when assembling the caliper body to the carrier.
•
When installing the caliper body, turn the brake piston clockwise using a tool such as the long nose pliers (A) to press it in.

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Installation illustration

•
Check the piston groove position before installing the caliper body.

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Installation illustration

2.
Fill the brake reservoir with brake fluid and perform air bleeding.
(Refer to Brake System - "Brake Bleeding Procedures")
3.
After installation, adjust the parking brake according to the parking brake specification.
•
EPB - (Refer to Parking Brake System - "Electronic Parking Brake (EPB)")
•
None EPB - (Refer to Parking Brake System - "Parking Brake Lever")
4.
Depress the brake pedal several times to ensure that the brake pads are correctly positioned, then check operation.
5.
Check the brake fluid leakage and pedal operating condition.
6.
Check if the parking brake is operating normally.

Brake Pad Replacement

Special Service Tool
Tool Name / Number
Illustration
Description
Piston expander
09581 - 11000

Brake System — Brake System / Brake Pad / Replacement / Special Service Tool illustration

Spreading the front brake caliper piston.

Replacement
Front brake pad
1.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Remove the guide rod lower bolt (A) and then open the caliper body (B).

Tightening torque :
21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Brake System — Brake System / Brake Pad / Replacement illustration

3.
Remove the return springs (A).

Brake System — Brake System / Brake Pad / Replacement illustration

4.
Remove the brake pads (A).

Brake System — Brake System / Brake Pad / Replacement illustration

5.
Remove the pad retainers (A).

Brake System — Brake System / Brake Pad / Replacement illustration

Note    
When replacing the brake pads, replace brake pads (A), retainers (B), and return springs (C) together.

Brake System — Brake System / Brake Pad / Replacement illustration

6.
Install in reverse order of removal.
Note    
•
Be careful not to damage the piston when pressing it.
•
Be careful not to touch the piston when installing the caliper body to the torque member.
•
Press the brake piston using SST (09581 - 11000) when installing the caliper body.

Brake System — Brake System / Brake Pad / Replacement illustration

7.
Depress the brake pedal several times to ensure that the brake pads are correctly positioned, then check operation.
Rear brake pad
1.
Release the parking brake.
• EPB : Release the parking brake by using the KDS.
(Refer to Brake System - "Electronic Parking Brake (EPB)")
• None EPB : Release the hand lever parking brake fully.
2.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
3.
Disconnect the EPB actuator connector or parking brake cable.
• EPB : Disconnect the EPB actuator connector (A).

Brake System — Brake System / Brake Pad / Replacement illustration

• None EPB : Remove the clip (A), and then separate the parking brake cable (B).
[2WD]

Brake System — Brake System / Brake Pad / Replacement illustration

[4WD]

Brake System — Brake System / Brake Pad / Replacement illustration

4.
Remove the caliper body (B) after removing the guide rod bolt (A).

Tightening torque :
21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Brake System — Brake System / Brake Pad / Replacement illustration

Note    
Secure the removed brake caliper body using a tool such as a cable tie.
5.
Remove the brake pads (A).

Brake System — Brake System / Brake Pad / Replacement illustration

6.
Remove the pad retainers (A).

Brake System — Brake System / Brake Pad / Replacement illustration

Note    
[None EPB]
•
When replacing the brake pads, replace brake pads, retainers, and return springs together.
•
Do not reuse the pad return spring.
•
Do not deform the pad return spring for installation.
•
Deformation can cause brake degradation, drag, and noise.
[EPB]
•
When replacing the brake pads, replace brake pads, retainers, and return springs together.
•
Ensure that there is no gap when installing the pad retainers.
•
Pad retainer gap can cause poor brake performance, drag, and noise.
•
Ensure that there is no deformation at the pad retainer retraction side.

Brake System — Brake System / Brake Pad / Replacement illustration

7.
Install in reverse order of removal.
Note    
•
Be careful not to interfere with the piston when assembling the caliper body to the carrier.
•
When installing the caliper body, turn the brake piston clockwise using a tool such as the long nose pliers (A) to press it in.

Brake System — Brake System / Brake Pad / Replacement illustration

•
Check the piston groove position before installing the caliper body.

Brake System — Brake System / Brake Pad / Replacement illustration

8.
Depress the brake pedal several times to ensure that the brake pads are correctly positioned, then check operation.
9.
Operate the parking brake several times to see if it works properly.
Note    
•
Release the parking brake using a KDS. [EPB]
(Refer to Brake System - "Electronic Parking Brake (EPB)")
•
After disassembling/assembling the caliper body or replacing the brake pads, parking brake cable, and brake disc, the parking brake should be adjusted. [None EPB]
(Refer to Brake System - "Parking Brake Lever")

Brake Pad Inspection

Inspection
Brake Pad Check
1.
Check brake pad thickness. If the thickness is thinner than the limit, replace the brake pads.

Front brake pad thickness
for 15 inch wheel standard : 11.0 mm (0.43 in.)
for 16 inch wheel : 11.5 mm (0.45 in.)
Service Limit : 2.0 mm (0.078 in.)


Rear brake pad thickness
Standard (EPB) : 10.0 mm (0.39 in.)
Standard (None EPB) : 9.0 mm (0.35 in.)
Service Limit : 2.0 mm (0.078 in.)

Brake System — Brake System / Brake Pad / Inspection illustration

2.
Check that grease is applied to sliding contact points and check the pad and backing metal for damage.

Vacuum Pump - G 1.6 T-GDI GAMMA ll Removal and Installation

Removal
1.
Remove the battery tray.
(Refer to Engine Electrical System - "Battery")
2.
Disconnect the wiring connector (A).

Brake System — Brake System / Vacuum Pump - G 1.6 T-GDI GAMMA ll / Removal and Installation / Removal illustration

3.
Remove the bolt and washer, and then separate the intercooler inlet pipe (A) to make a workspace.

Tightening torque :
18.6 - 23.5 N·m (1.9 - 2.4 kgf·m, 13.7 - 17.4 lb·ft)

Brake System — Brake System / Vacuum Pump - G 1.6 T-GDI GAMMA ll / Removal and Installation / Removal illustration

4.
Remove the vacuum hose (A) from the vacuum pump.

Brake System — Brake System / Vacuum Pump - G 1.6 T-GDI GAMMA ll / Removal and Installation / Removal illustration

5.
Remove the bolts, and then remove the vacuum pump (A).

Tightening torque :
19.6 - 29.4 N·m (2.0 - 3.0 kgf·m, 14.5 - 21.7 lb·ft)

Brake System — Brake System / Vacuum Pump - G 1.6 T-GDI GAMMA ll / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.

Other information:

Kia Seltos SP2 (2021-2026) Service Manual: AWD mode

AWD mode helps improve the driving performance of the Kia Seltos by controlling power delivery to all four wheels. This system supports better traction and stability when road conditions change, especially on wet, slippery, sandy, muddy, or uneven surfaces. You can switch from AWD AUTO mode to AWD Lock mode by pressing the AWD Lock mode switch.

Kia Seltos SP2 (2021-2026) Service Manual: Fuses

The electrical system of the Kia Seltos is protected from overload damage by fuses. These fuses are designed to interrupt the circuit when excessive current is detected, helping protect wiring, electrical components, and control systems. Blade type Cartridge type Multi fuse BFT * Left side: normal, right side: blown.