Owner's library Kia Seltos Manuals Owner's manual pages, service notes, maintenance references and practical Kia Seltos help in one clean library.

Kia Seltos reference pages

Manuals, maintenance notes and quick owner help.

Find Kia Seltos operating instructions, warning light explanations, service information and owner guidance without digging through a full PDF.

Kia Seltos: Brake System / Parking Brake System

Contents:

Components and Components Location

Component
Parking Brake - None EPB

Brake System — Parking Brake System / Components and Components Location / Component illustration

1. Parking Brake Lever
2. Parking Brake Cable Equalizer Assembly
3. Parking Brake Cable (LH)
4. Parking Brake Cable (RH)


Electronic Parking Brake - EPB

Brake System — Parking Brake System / Components and Components Location / Component illustration

1. ESC (Electronic Stability Control) Control Unit
2. EPB Switch

3. Electronic Parking Brake (EPB) Actuator


Parking Brake Lever Removal and Installation

Removal
1.
Disconnect the battery negative (-) terminal.
2.
Remove the floor console.
(Refer to Body - “Floor Console Assembly�)
3.
Remove the floor air duct (A) after removing the screws.

Brake System — Parking Brake System / Parking Brake Lever / Removal and Installation / Removal illustration

4.
Remove the floor console bracket (A) after removing the nuts.

Tightening torque :
3.3 - 4.2 N·m (0.34 - 0.43 kgf·m, 2.5 - 3.1 lb·ft)

Brake System — Parking Brake System / Parking Brake Lever / Removal and Installation / Removal illustration

5.
Disconnect the parking brake switch connector (A).

Brake System — Parking Brake System / Parking Brake Lever / Removal and Installation / Removal illustration

6.
Remove the cable retainer (A) and the parking brake cables (B).

Brake System — Parking Brake System / Parking Brake Lever / Removal and Installation / Removal illustration

7.
Remove the parking brake lever (A) after removing the bolts.

Tightening torque :
19.6 - 29.4 N·m (2.0 - 3.0 kgf·m, 14.5 - 21.7 lb·ft)

Brake System — Parking Brake System / Parking Brake Lever / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.
2.
Adjust the parking brake cable and check it operating normally.
(Refer to Parking Brake Lever - "Adjustment")

Parking Brake Lever Adjustment

Inspection
Note    
After disassembling/assembling the torque member or replacing the caliper, parking brake cable or brake disc, re-adjust the parking brake.
1.
To fit the cable, follow one of these procedures before adjusting.
–
Apply a parking brake fully more than 3 times
–
With full operation, hold the parking brake for 1 to 2 hours.
2.
Remove the floor console assembly.
(Refer to Body - "Floor Console Assembly")
3.
After fitting the cable, adjust the parking brake cable so that the stroke is 5 - 6 notch when operating the pedal with 30kgf at point (A).

Brake System — Parking Brake System / Parking Brake Lever / Adjustment / Inspection illustration

Note    
•
For the BIR type, adjust the adjustment nut of the lever assembly so that the sum of the O / P lever (A) and the stopper (B) (LH / RH) angle is within 3.0 mm (0.11 in).

Brake System — Parking Brake System / Parking Brake Lever / Adjustment / Inspection illustration

•
Adjust the parking brake cable by tightening or loosening the adjusting nut (A).

Brake System — Parking Brake System / Parking Brake Lever / Adjustment / Inspection illustration

4.
Make sure that there is no gap between adjustment nut and clip after adjusting the parking brake.
5.
Make sure that the brakes are not drag.
6.
Make sure that the parking brake switch is 'ON' before the parking lever is operated by 1 notch and 'OFF' when released.
7.
Check whether the wheel operates smoothly.
8.
Perform driving test.

Parking Brake Cable Removal and Installation

Removal
1.
Disconnect the battery negative (-) terminal.
2.
Remove the floor console.
(Refer to Body - “Floor Console Assembly�)
3.
Remove the floor air duct (A) after removing the screws.

Brake System — Parking Brake System / Parking Brake Cable / Removal and Installation / Removal illustration

4.
Remove the floor console bracket (A) after removing the nuts.

Tightening torque :
3.3 - 4.2 N·m (0.34 - 0.43 kgf·m, 2.5 - 3.1 lb·ft)

Brake System — Parking Brake System / Parking Brake Cable / Removal and Installation / Removal illustration

5.
Remove the cable retainer (A) and the parking brake cables (B).

Brake System — Parking Brake System / Parking Brake Cable / Removal and Installation / Removal illustration

6.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
7.
Remove the clip (A), and the parking brake cable (B).
[2WD]

Brake System — Parking Brake System / Parking Brake Cable / Removal and Installation / Removal illustration

[4WD]

Brake System — Parking Brake System / Parking Brake Cable / Removal and Installation / Removal illustration

8.
Remove the parking brake cable (B) after removing the bolts (A).

Tightening torque :
19.6 - 29.4 N·m (2.0 - 3.0 kgf·m, 14.5 - 21.7 lb·ft)

Brake System — Parking Brake System / Parking Brake Cable / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.
2.
Adjust the parking brake cable and check it operating normally.
(Refer to Parking Brake Lever - "Adjustment")

Parking Brake Cable Adjustment

Inspection
Note    
After disassembling/assembling the torque member or replacing the caliper, parking brake cable or brake disc, re-adjust the parking brake.
1.
To fit the cable, follow one of these procedures before adjusting.
–
Apply a parking brake fully more than 3 times
–
With full operation, hold the parking brake for 1 to 2 hours.
2.
Remove the floor console assembly.
(Refer to Body - "Floor Console Assembly")
3.
After fitting the cable, adjust the parking brake cable so that the stroke is 5 - 6 notch when operating the pedal with 30kgf at point (A).

Brake System — Parking Brake System / Parking Brake Cable / Adjustment / Inspection illustration

Note    
•
For the BIR type, adjust the adjustment nut of the lever assembly so that the sum of the O / P lever (A) and the stopper (B) (LH / RH) angle is within 3.0 mm (0.11 in).

Brake System — Parking Brake System / Parking Brake Cable / Adjustment / Inspection illustration

•
Adjust the parking brake cable by tightening or loosening the adjusting nut (A).

Brake System — Parking Brake System / Parking Brake Cable / Adjustment / Inspection illustration

4.
Make sure that there is no gap between adjustment nut and clip after adjusting the parking brake.
5.
Make sure that the brakes are not drag.
6.
Make sure that the parking brake switch is 'ON' before the parking lever is operated by 1 notch and 'OFF' when released.
7.
Check whether the wheel operates smoothly.
8.
Perform driving test.

Electronic Parking Brake (EPB) Description and Operation ➤

Electronic Parking Brake (EPB) Adjustment

Adjustment
Brake pad replacement mode
This function operates the EPB actuator to release the electronic parking brake before replacing the brake pads.
(S/W Management → Brake → Brake Pad Change Mode)
Information    
Refer to the KDS screen for operating conditions and details.

Electronic Parking Brake (EPB) On Vehicle Inspection

On Vehicle Inspection
1.
The electronic parking brake system driving can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
(1) Self Diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS
(2) Sensor data : Checks the system input/output values
(3) Forced operation : Checks the system operating status
(4) Additional function : Controls system options, zero adjustment, and other functions

Electronic Parking Brake (EPB) Removal and Installation

Removal
EPB Switch
1.
Remove the console upper cover.
(Refer to Body - "Console Upper Cover")
EPB Actuator
1.
Remove the EPB actuator (rear caliper body).
(Refer to Brake System - "Rear Brake Caliper")
EPB Control Module (ESC (Electronic Stability Control) System)
1.
Remove the ESC Control Unit.
(Refer to ESC (Electronic Stability Control) System - "ESC Control Unit")
Installation
1.
Install in reverse order of removal.

Other information:

Kia Seltos SP2 (2021-2026) Service Manual: Smart key immobilizer system

The Kia Seltos smart key immobilizer system helps protect the vehicle from theft. If an incorrectly coded key or an unauthorized electronic device is used, the vehicle's power system may be disabled and the engine may not start. When the ENGINE START/STOP button is placed in the ON position, the immobilizer system indicator should illuminate briefly and then turn off.

Kia Seltos SP2 (2021-2026) Service Manual: Electronic Parking Brake (EPB) Description and Operation

Description The Electric Parking Brake (EPB) is a parking brake system that operates the actuators of each caliper using an electrical signal via button operation, unlike a parking brake operated by a lever or pedal. The EPB has the function to engage the parking brake when the vehicle is stationary, to assist in braking in emergencies due to brake failure, and to engage the parking brake automatically when the engine off.