Owner's library Kia Seltos Manuals Owner's manual pages, service notes, maintenance references and practical Kia Seltos help in one clean library.

Kia Seltos reference pages

Manuals, maintenance notes and quick owner help.

Find Kia Seltos operating instructions, warning light explanations, service information and owner guidance without digging through a full PDF.

Kia Seltos: Body Electrical System / Button Engine Start System

Contents:

Description and Operation

Description
System Overview
The system offers the following features:
–
Switching between off, IG ON and power by pushing the start button.
–
Controls external relays for ACC / IG1 / IG2 terminal switching and STARTER, without use of mechanical IG switch.
–
Indicating the vehicle status on cluster by displaying messages.
–
Immobilizer function by LF transponder communication between between fob and button start switch.
–
Interface with Low Speed CAN vehicle communication network.
–
Interface with LIN vehicle communication network depending on platform.
System Main Function
•
Switching of ACC/IG1/IG2 terminal.
•
Control of the STARTER relay based on communication with EMS ECU.
•
Management of the Immobilizer function.
•
Management of Button Start System warning function.
Wireless Communications
The electric signal is used to exchange information between vehicle and FOB key. For now, button start is applied with smart key FOB key together.
Smart key function is explained separately so refer to the corresponding system contents.
System Diagram

Body Electrical System — Button Engine Start System / Description and Operation / Description illustration

*SSB : Start Stop Button
Schematic Diagram

Body Electrical System — Button Engine Start System / Description and Operation / Description illustration

Integrated Body Control Unit (IBU)
The IBU manages all functions related to:
–
Start/Stop Button (SSB) control
–
Immobilizer communication (with ECM for releasing immobilizer)
–
Authentication server (Validity of Transponder and in case of Smart Key option Passive FOB authentication)
–
System consistency monitoring
–
System diagnosis
–
Control of display message / warning buzzer
Limp Home Mode
–
In case of no input signal for the brake switch (AT specification), the ACC mode shall cycle to “START� by pressing SSB for more than 10 seconds.
–
In case of problems with communication between EMS and CAN (the EMS state), the “START� state cycles to the “ENGINE RUN� based on rpm input.
–
In case that one out of two SSB input lines is disconnected, the electric power cycling is available when SSB is pressed twice within 10 seconds.
The buzzer rings when the button is pressed for the first time.
Electric power cycling is available and buzzer stops when the button is pressed twice within 10 seconds.

Body Electrical System — Button Engine Start System / Description and Operation / Description illustration

Terminal and Starter Relay
Relay is used to switch the terminal ACC / IG1 / IG2.
Normally-open relay is operated by smart key unit.
One relay coil is connected to output terminal of IBU.

Start/stop button Terminal Function

Connector and Terminal Function

Body Electrical System — Button Engine Start System / Start/stop button / Terminal Function / Connector and Terminal Function illustration

Connector A
Terminal
Function
Terminal
Function

Body Electrical System — Button Engine Start System / Start/stop button / Terminal Function / Connector and Terminal Function illustration

1
SSB Switch 1
6
Ground
2
-
7
SSB Switch 2
3
SSB Illumination ( + )
8
Illumination ( - )
4
Immobilizer (Power)
9
-
5
-
10
Immobilizer (Ground)

Start/stop button Removal and Installation

Removal
1.
Remove the crash pad garnish [Passenger's side].
(Refer to Body - "Crash Pad Garnish")
2.
Remove the Start / Stop Button (SSB) (A) after removing the screws.

Body Electrical System — Button Engine Start System / Start/stop button / Removal and Installation / Removal illustration

Body Electrical System — Button Engine Start System / Start/stop button / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.

Other information:

Kia Seltos SP2 (2021-2026) Service Manual: Selecting a CRS

When selecting a Child Restraint System for your child, always choose a restraint that fits the child, fits the Kia Seltos seating position, and can be installed according to the manufacturer's instructions. Make sure the CRS has a label certifying that it meets FMVSS 213. Select a child restraint based on your child's height and weight.

Kia Seltos SP2 (2021-2026) Service Manual: Troubleshooting

Troubleshooting Failure Diagnosis 1. In principle, ESC and TCS controls are prohibited in case of ABS failure. 2. When ESC or TCS fails, only the failed system control is prohibited. 3.