Kia Seltos SP2 (2021-2026) Service Manual / Engine Control / Fuel System / Engine Control System / Description and Operation
Kia Seltos: Engine Control System / Description and Operation
| OBD-II review |
1. Overview
The California Air Resources Board (CARB) began regulation of On Board Diagnostics (OBD) for vehicles sold in
California beginning with the 1988 model year. The first phase, OBD-I, required monitoring of the fuel metering
system, Exhaust Gas Recirculation (EGR) system and additional emission related components. The Malfunction Indicator
Lamp (MIL) was required to light and alert the driver of the fault and the need for repair of the emission control
system. Associated with the MIL was a fault code or Diagnostic Trouble Code (DTC) idenfying the specific area of the
fault.
The OBD system was proposed by CARB to improve air quality by identifying vehicle exceeding emission standards.
Passage of the Federal Clean Air Act Amendments in 1990 has also prompted the Environmental Protection Agency (EPA)
to develop On Board Diagnostic requirements. CARB OBD-II regulations were followed until 1999 when the federal
regulations were used.
The OBD-II system meets government regulations by monitoring the emission control system. When a system or
component exceeds emission threshold or a component operates outside tolerance, a DTC will be stored and the MIL
illuminated.
The diagnostic executive is a computer program in the Engine Control Module (ECM) or PowertrainControl Module
(PCM) that coordinates the OBD-II self-monitoring system. This program controls all the monitors and interactions,
DTC and MIL operation, freeze frame data and scan tool interface.
Freeze frame data describes stored engine conditions, such as state of the engine, state of fuel control, spark,
RPM, load and warm status at the point the first fault is detected. Previously stored conditions will be replaced
only if a fuel or misfire fault is detected. This data is accessible with the scan tool to assist in repairing the
vehicle.
The center of the OBD-II system is a microprocessor called the Engine Control Module (ECM) or Powertrain Control
Module(PCM).
The ECM or PCM receives input from sensors and other electronic components (switches, relays, and others) based
on information received and programmed into its memory (keep alive random access memory, and others), the ECM or PCM
generates output signals to control various relays, solenoids and actuators.
2. Configuration of hardware and related terms
1) GST (Generic scan tool)
2) MIL (Malfunction indication lamp) - MIL activity by transistor
The Malfunction Indicator Lamp (MIL) is connected between ECM or PCM-terminal Malfunction Indicator Lamp and
battery supply (open collector amplifier).
In most cars, the MIL will be installed in the instrument panel. The lamp amplifier can not be damaged by a short
circuit.
Lamps with a power dissipation much greater than total dissipation of the MIL and lamp in the tester may cause a
fault indication.
â–· At ignition ON and engine revolution (RPM)< MIN. RPM, the MIL is switched ON for an optical check by the
driver.
3) MIL illumination
When the ECM or PCM detects a malfunction related emission during the first driving cycle, the DTC and engine
data are stored in the freeze frame memory. The MIL is illuminated only when the ECM or PCM detects the same
malfunction related to the DTC in two consecutive driving cycles.
4) MIL elimination
| • |
Misfire and Fuel System Malfunctions:
For misfire or fuel system malfunctions, the MIL may be eliminated if the same fault does not reoccur
during monitoring in three subsequent sequential driving cycles in which conditions are similar to those
under which the malfunction was first detected.
|
| • |
All Other Malfunctions:
For all other faults, the MIL may be extinguished after three subsequent sequential driving cycles during
which the monitoring system responsible for illuminating the MIL functions without detecting the malfunction
and if no other malfunction has been identified that would independently illuminate the MIL according to the
requirements outlined above.
|
5) Erasing a fault code
The diagnostic system may erase a fault code if the same fault is not re-registered in at least 40 engine warm-up
cycles, and the MIL is not illuminated for that fault code.
6) Communication Line (CAN)
| • |
Bus Topology : Line (bus) structure
|
| • |
Wiring : Twisted pair wire
|
| • |
Off Board DLC Cable Length : Max. 5m
|
| • |
Data Transfer Rate
|
| – |
Diagnostic : 500 kbps
|
| – |
Service Mode (Upgrade, Writing VIN) : 500 or 1Mbps)
|
7) Driving cycle
A driving cycle consists of engine start up, and engine shut off.
8) Warm-up cycle
A warm-up cycle means sufficient vehicle operation such that the engine coolant temperature has risen by at least
40 degrees Fahrenheit from engine starting and reaches a minimum temperature of at least 160 degrees Fahrenheit.
9) DTC format
| • |
Diagnostic Trouble Code (SAE J2012)
|
| • |
DTCs used in OBD-II vehicles will begin with a letter and are followed by four numbers.
|
The letter of the beginning of the DTC identifies the function of the monitored device that has failed. A "P"
indicates a powertrain device, "C" indicates a chassis device. "B" is for body device and "U" indicates a network or
data link code. The first number indicates if the code is generic (common to all manufacturers) or if it is
manufacturer specific. A "0" & "2" indicates generic, "1" indicates manufacturer-specific. The second number
indicates the system that is affected with a number between 1 and 7.
The following is a list showing what numbers are assigned to each system.
| • |
1 : Fuel and air metering
|
| • |
2 : Fuel and air metering(injector circuit malfunction only)
|
| • |
3 : Ignition system or misfire
|
| • |
4 : Auxiliary emission controls
|
| • |
5 : Vehicle speed controls and idle control system
|
| • |
6 : Computer output circuits
|
| • |
7 : Transmission
|
The last two numbers of the DTC indicates the component or section of the system where the fault is located.
10) Freeze frame data
When a freeze frame event is triggered by an emission related DTC, the ECM or PCM stores various vehicle
information as it existed the moment the fault ocurred. The DTC number along with the engine data can be useful in
aiding a technician in locating the cause of the fault. Once the data from the 1st driving cycle DTC ocurrence is
stored in the freeze frame memory, it will remain there even when the fault ocurrs again (2nd driving cycle) and the
MIL is illuminated.
| • |
Freeze Frame List
|
| a. |
Calculated Load Value
|
| b. |
Engine RPM
|
| c. |
Fuel Trim
|
| d. |
Fuel Pressure (if available)
|
| e. |
Vehicle Speed (if available)
|
| f. |
Coolant Temperature
|
| g. |
Intake Manifold Pressure (if available)
|
| h. |
Closed-or Open-loop operation
|
| i. |
Fault code
|
3. OBD-II Readiness Test
[Kia Motors Drive Cycle]
Kia OBDII Drive Cycle is designed to execute and complete the OBDII monitors. To complete a specific monitor for
repair verification, follow the Drive Cycle chart below.
Kia OBDII Drive Cycle consists of two modes (Mode 1 and Mode 2) and the Mode 2 is to perform the catalyst
diagnostics on Dephi EMS only.
| – |
Continental, Bosch or Kefico EMS : Mode 1 drive cycle should be done one time for diagnostics on all
systems.
|
| – |
Dephi EMS : Mode 2 drive cycle should be done two times in a row after Mode 1 is carried out one time for
diagnostics on all systems
|
| • |
Mode 1
|
| • |
Mode 2
|
| Mode |
No |
Operation |
Speed (mph) |
Duration (s) |
E/Time (s) |
Remarks |
| Mode 1 |
1 |
Engine Start |
0 |
0 |
0 |
ECT @ Start 32-104°F |
| 2 |
Idling (N) |
0 |
30 |
30 |
Neutral Range |
|
| 3 |
Idling (D) |
0 |
270 |
300 |
D Range |
|
| 4 |
Acceleration |
0 → 50 |
15 |
315 |
|
|
| 5 |
Steady Speed |
50 |
230 |
545 |
|
|
| 6 |
Deceleration |
50 → 45 |
5 |
550 |
|
|
| 7 |
Steady Speed |
45 |
5 |
555 |
|
|
| 8 |
Acceleration |
45 → 55 |
5 |
560 |
|
|
| 9 |
Steady Speed |
55 |
5 |
565 |
|
|
| 10 |
Deceleration |
55 → 45 |
5 |
570 |
|
|
| 11 |
Steady Speed |
45 |
5 |
575 |
|
|
| 12 |
Repeat 8 through 11 ten times. |
- |
180 |
755 |
|
|
| 13 |
Acceleration |
45 → 55 |
5 |
760 |
|
|
| 14 |
Steady Speed |
55 |
5 |
765 |
|
|
| 15 |
Deceleration |
55 → 0 |
45 |
810 |
|
|
| 16 |
Idling (D) |
0 |
120 |
930 |
D Range |
|
| 17 |
Idling (N) |
0 |
760 |
1690 |
Neutral Range |
|
| 18 |
Acceleration |
0 → 55 |
15 |
1705 |
|
|
| 19 |
Steady Speed |
55 |
60 |
1765 |
|
|
| 20 |
Deceleration |
55 → 0 |
15 |
1780 |
|
|
| 21 |
Idling (D) |
0 |
60 |
1840 |
D Range |
|
| 22 |
Acceleration |
0 → 55 |
15 |
1855 |
|
|
| 23 |
Steady Speed |
55 |
60 |
1915 |
|
|
| 24 |
Deceleration |
55 → 0 |
15 |
1930 |
|
|
| 25 |
Idling (D) |
0 |
60 |
1990 |
D Range |
|
| 26 |
Acceleration |
0 → 40 |
15 |
2005 |
|
|
| 27 |
Steady Speed |
40 |
15 |
2020 |
|
|
| 28 |
Acceleration |
40 → 50 |
15 |
2035 |
|
|
| 29 |
Steady Speed |
50 |
5 |
2040 |
|
|
| 30 |
Deceleration |
50 → 40 |
15 |
2055 |
|
|
| 31 |
Steady Speed |
40 |
60 |
2115 |
|
|
| 32 |
Repeat 28 through 31 five times. |
- |
380 |
2495 |
|
|
| 33 |
Acceleration |
40 → 50 |
15 |
2510 |
|
|
| 34 |
Steady Speed |
50 |
5 |
2515 |
|
|
| Mode 1 |
35 |
Deceleration |
50 → 0 |
40 |
2555 |
|
| 36 |
Idling (D) |
0 |
25 |
2580 |
D Range |
|
| Mode 2 |
1 |
Engine Start |
0 |
0 |
0 |
|
| 2 |
Idling (N) |
0 |
30 |
30 |
Neutral Range |
|
| 3 |
Idling (D) |
0 |
210 |
240 |
D Range |
|
| 4 |
Acceleration |
0 → 49 |
16 |
256 |
|
|
| 5 |
Deceleration |
49 → 47 |
2 |
258 |
Lift Foot Up : APS = 0 |
|
| 6 |
Steady Speed |
47 |
10 |
268 |
|
|
| 7 |
Acceleration |
47 → 55 |
4 |
272 |
Middle Tip In or Deep Accel |
|
| 8 |
Deceleration |
55 → 52 |
3 |
275 |
Lift Foot Up : APS = 0 |
|
| 9 |
Steady Speed |
52 |
10 |
285 |
|
|
| 10 |
Deceleration |
52 → 45 |
3 |
288 |
Lift Foot Up : APS = 0 |
|
| 11 |
Acceleration |
45 → 47 |
2 |
290 |
|
|
| 12 |
Repeat 6 through 11 twelve times. |
- |
330 |
620 |
|
|
| 13 |
Steady Speed |
47 |
57 |
677 |
|
|
| 14 |
Deceleration |
47 → 0 |
8 |
685 |
|
|
| 15 |
Idling (D) |
0 |
60 |
745 |
D Range |
|
| 16 |
Acceleration |
0 → 50 |
15 |
760 |
|
|
| 17 |
Steady Speed |
50 |
90 |
850 |
|
|
| 18 |
Deceleration |
50 → 0 |
10 |
860 |
|
|
| 19 |
Repeat 15 through 18 two times. |
- |
175 |
1035 |
|
|
| 20 |
Idling (D) |
0 |
90 |
1125 |
D Range |
1) Catalyst monitoring
The catalyst efficiency monitor is a self-test strategy within the ECM or PCM that uses the downstream Heated
Oxygen Sensor (HO2S) to determine when a catalyst has fallen below the minimum level of effectiveness in its ability
to control exhaust emission.
2) Misfire monitoring
Misfire is defined as the lack of proper combustion in the cylinder due to the absence of spark, poor fuel
metering, or poor compression. Any combustion that does not occur within the cylinder at the proper time is also a
misfire. The misfire detection monitor detects fuel, ignition or mechanically induced misfires. The intent is to
protect the catalyst from permanent damage and to alert the customer of an emission failure or an inspection
maintenance failure by illuminating the MIL . When a misfire is detected, special software called freeze frame data
is enabled. The freeze frame data captures the operational state of the vehicle when a fault is detected from
misfire detection monitor strategy.
3) Fuel system monitoring
The fuel system monitor is a self-test strategy within the ECM or PCM that monitors the adaptive fuel table The
fuel control system uses the adaptive fuel table to compensate for normal variability of the fuel system components
caused by wear or aging. During normal vehicle operation, if the fuel system appears biased lean or rich, the
adaptive value table will shift the fuel delivery calculations to remove bias.
4) Engine cooling system monitoring
The cooling system monitoring is a self-test strategy within the ECM or PCM that monitors ECTS (Engine Coolant
Temperature Sensor) and thermostat about circuit continuity, output range, rationality faults.
5) O2 sensor monitoring
OBD-II regulations require monitoring of the upstream Heated O2 Sensor (H2OS) to detect if the deterioration of
the sensor has exceeded thresholds. An additional HO2S is located downstream of the Warm-Up Three Way Catalytic
Converter (WU-TWC) to determine the efficiency of the catalyst.
Although the downstream H2OS is similar to the type used for fuel control, it functions differently. The
downstream HO2S is monitored to determine if a voltage is generated. That voltage is compared to a calibrated
acceptable range.
6) Evaporative emission system monitoring
The EVAP. monitoring is a self-test strategy within the ECM or PCM that tests the integrity of the EVAP. system.
The complete evaporative system detects a leak or leaks that cumulatively are greater than or equal to a leak caused
by a 0.040 inch and 0.020 inch diameter orifice.
7) Air conditioning system monitoring
The A/C system monitoring is a self-test strategy within the ECM or PCM that monitors malfunction of all A/C
system components at A/C ON.
8) Comprehensive components monitoring
The comprehensive components monitoring is a self-test strategy within the ECM or PCM that detects fault of any
electronic powertrain components or system that provides input to the ECM or PCM and is not exclusively an input to
any other OBD-II monitor.
9) A/C system component monitoring
Requirement:
If a vehicle incorporates an engine control strategy that alters off idle fuel and/or spark control when the A/C
system is on, the OBD II system shall monitor all electronic air conditioning system components for malfunctions
that cause the system to fail to invoke the alternate control while the A/C system is on or cause the system to
invoke the alternate control while the A/C system is off.
Additionally, the OBD II system shall monitor for malfunction all electronic air conditioning system components
that are used as part of the diagnostic strategy for any other monitored system or component.
Implementation plan:
No engine control strategy incorporated that alters offidle fuel and/or spark control when A/C system is on.
Malfuction of A/C system components is not used as a part of the diagnostic strategy for other monitored system or
component.
Other information:
Kia Seltos SP2 (2021-2026) Service Manual: Tire sidewall labeling
Tire sidewall information identifies and describes the basic characteristics of the tire. It also provides the Tire Identification Number (TIN), which is used for safety standard certification and may help identify a tire in case of a recall. The TIN can be used to identify the tire if a safety recall or service campaign applies.Troubleshooting Failure Diagnosis 1. In principle, ESC and TCS controls are prohibited in case of ABS failure. 2. When ESC or TCS fails, only the failed system control is prohibited. 3.