Owner's library Kia Seltos Manuals Owner's manual pages, service notes, maintenance references and practical Kia Seltos help in one clean library.

Kia Seltos reference pages

Manuals, maintenance notes and quick owner help.

Find Kia Seltos operating instructions, warning light explanations, service information and owner guidance without digging through a full PDF.

Kia Seltos: Body Electrical System / Smart Key System

Contents:

Specification

Specification
Integrated Body Control Unit (IBU)
Item
Specification
Rated voltage (V)
12
Operating voltage (V)
9 - 16
Operating temperature [°C (°F)]
-40 to 85 (-40 to 185)

RF Receiver
Item
Specification
Frequency (MHz)
433.92
Antenna type
FSK

Smart Key
Item
Specification
Fob key
Battery
Lithium battery 3V 1 unit
Distance
- The distance over which Radio Frequency (RF) Receiver can receive a FOB transmission signal : 30 m (98.4 ft.)
- The distance over which Low Frequency (LF) antenna(Outer Handle/ Tailgate ) can detect FOB : 0.7 m (2.29 ft.)
Battery life
More than 2 years (20 times / a day)
Caution    
An inappropriately disposed battery can be harmful to the environment and human health.
Push buttons
3 buttons (Door lock / unlock, Tailgate open)
4 buttons (Door lock / unlock, Tailgate open, Remote start)
LF Frequency (KHz)
125
RF Frequency (MHz)
433.92
Numbers
2 units

Antenna
Item
Specification
Rated voltage (V)
12
Operating voltage (V)
9 - 16
Operating temperature [°C (°F)]
-30 to 80 (-22 to 176)
Frequency (KHz)
125
Numbers
Interior (2 units), Door (2 units), Rear Bumper (1 unit)

Components and Components Location

Component

Body Electrical System — Smart Key System / Components and Components Location / Component illustration

1. Integrated Body control Unit (IBU)
2. Smart Key Antenna
3. Buzzer
4. Smart Key Antenna (Door Outside Handle)

Description and Operation ➤

On Vehicle Inspection

On Vehicle Inspection
Diagnosis with KDS
1.
The smart key system can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
(1)
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
(2)
S/W Management : Controlling other features including system option setting and zero point adjustment.
(S/W Management → Integrated Body Control Unit-SMK → Smart Key Code Saving)
(S/W Management → Integrated Body Control Unit-SMK → Antenna Status Check)
(S/W Management → Integrated Body Control Unit-SMK → FOB KEY STATUS INFORMATION)
(S/W Management → Integrated Body Control Unit-SMK → SMK STATUS INFORMATION)
(S/W Management → Integrated Body Control Unit-SMK → Neutralization Mode)
Information    
Refer to the KDS screen for operating conditions and details.

Code Saving

Code Saving
Information    
Refer to the KDS screen for operating conditions and details.
Smart Key Code Saving
1.
Perform the order below with the KDS when registering the smart key.
(S/W Management → IBU-SMK → Smart Key Code Saving)
Smart Key Status Check
1.
Perform the order below with the KDS when checking the operation of the smart key.
(S/W Management → IBU-SMK → SMK STATUS INFORMATION)

Smart Key Unit Removal and Installation

Removal
Integrated Body Control Unit (IBU)
1.
Remove the Integrated Body Control Unit (IBU).
(Refer to Body Electrical System - "Integrated Body Control Unit (IBU)")
Front Door Outside Handle
1.
Remove the door outside handle.
(Refer to Front Door - "Front Door Handle")
Tailgate Outside Handle
1.
Remove the tailgate outside handle assembly.
(Refer to Body - "Tailgate Outside Handle")
Buzzer
1.
Remove the front bumper assembly.
(Refer to Body - "Front Bumper Assembly")
2.
Disconnect the buzzer connector (A).

Body Electrical System — Smart Key System / Smart Key Unit / Removal and Installation / Removal illustration

3.
Remove the buzzer (A).

Body Electrical System — Smart Key System / Smart Key Unit / Removal and Installation / Removal illustration

Information    
Clip position :

Body Electrical System — Smart Key System / Smart Key Unit / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.

Smart Key Unit Inspection

Inspection
Integrated Body Control Unit (IBU)
1.
Inspect the IBU with the KDS.
(Refer to Smart Key System - "On Vehicle Inspection")
Front Door Outside Handle
1.
Remove the door outside handle.
(Refer to Body - "Front Door Outside Handle")
2.
Disconnect the front door outside handle connector and then check for continuity between terminals No 1 and No 6.

Body Electrical System — Smart Key System / Smart Key Unit / Inspection illustration

Terminal
Function
SMK
NFC
1
Battery (+)
Battery (+)
2
-
L-CAN (Low)
3
Driver's door lock/unlock switch
Driver's door lock switch
4
Driver's door antenna (ground)
Driver's door unlock switch
5
-
L-CAN (High)
6
Ground
Ground

Tailgate Outside Handle Switch
1.
Remove the tailgate lid lower trim.
(Refer to Body - " Tailgate Lid Trim")
2.
Check for continuity between the terminals.
[Type A]

Body Electrical System — Smart Key System / Smart Key Unit / Inspection illustration

Terminal
Function
Switch OFF
Switch ON
3 - 4
No continuity
Continuity

[Type B]

Body Electrical System — Smart Key System / Smart Key Unit / Inspection illustration

Terminal
Function
Switch OFF
Switch ON
3 - 4
No continuity
Continuity

Smart Key Antenna Removal and Installation

Removal
Interior Antenna 1
1.
Remove the floor console assembly.
(Refer to Body - “Floor Console Assembly�)
2.
Disconnect the interior antenna 1 connector (A).

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

3.
Remove the interior antenna 1 (A) after removing the nuts.

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

Interior Antenna 3
1.
Disconnect the negative ( - ) battery terminal.
2.
Remove the rear transverse trim.
(Refer to Body - "Rear Transverse Trim")
3.
Disconnect the interior antenna 3 connector (A).

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

4.
Remove the interior antenna 3 (A) after removing the nuts.

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

Front Door Antenna #1
1.
Remove the front door trim.
(Refer to Body - "Front Door Trim")
2.
Disconnect the front door antenna connector (A).

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

3.
Remove the front door antenna (A) after removing the screws.

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

Information    
Clip position :

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

Front Door Antenna #2
1.
Remove the front door outside handle.
(Refer to Body - "Front Door Outside Handle")
2.
Remove the handle cover (A) after removing the screw.
Driver's Side

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

Passenger's Side

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

Note    
Remove the handle cover (A) by pulling it in the direction of the arrow.

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

3.
Remove the antenna.
(1)
Move the antenna wiring (A) to (B) by pulling it in the direction of the arrow.

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

(2)
Remove the antenna (A) by pulling it in the direction of the arrow.

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

Rear Bumper Antenna
1.
Disconnect the negative ( - ) battery terminal.
2.
Remove the rear bumper antenna connector (A).

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

3.
Remove the rear bumper antenna (A) after removing the screws.

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.
Front Door Antenna #2
1.
Install in reverse order of removal.
Note    
Install the handle cover as the procedures below.
1)
Fix the handle's (A) area to handle cover's (B) area.

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Installation illustration

2)
Install the handle cover (A) by pushing it in the derection of the arrow.

Body Electrical System — Smart Key System / Smart Key Antenna / Removal and Installation / Installation illustration

Other information:

Kia Seltos SP2 (2021-2026) Service Manual: Automatic climate control system

The Kia Seltos automatic climate control system uses cooling, heating, air intake, fan speed, and air distribution control to help maintain a pleasant cabin environment. When AUTO mode is selected, the system automatically adjusts several settings to reach the selected temperature. Type A Type B Fan speed control button Air intake control button Mode selection button Rear window defroster button Temperature control knob Air conditioning (A/C) button OFF button Front windshield defroster button AUTO automatic control button Climate control display NOTICE Operating the blower when the ignition switch is in the ON position without the engine running may discharge the battery.

Kia Seltos SP2 (2021-2026) Service Manual: Description and Operation

Description Burglar Alarm State [B/A State] B/A State Description DISARM 1) This is the state when "ARM" mode is off. 2) If all doors or hood or tailgate are opened, there is no alarm sound.