Owner's library Kia Seltos Manuals Owner's manual pages, service notes, maintenance references and practical Kia Seltos help in one clean library.

Kia Seltos reference pages

Manuals, maintenance notes and quick owner help.

Find Kia Seltos operating instructions, warning light explanations, service information and owner guidance without digging through a full PDF.

Kia Seltos: Restraint / Airbag Module

Contents:

Components and Components Location

Component

Restraint — Airbag Module / Components and Components Location / Component illustration

1. Driver Airbag (DAB) Module
2. Clock Spring
3. Passenger Airbag (PAB) Module

4. Curtain Airbag (CAB) Module
5. Side Airbag (SAB) Module


On Vehicle Inspection

On Vehicle Inspection
Diagnosis with KDS
1.
The airbag system can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
(1)
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
Information    
Refer to the KDS screen for operating conditions and details.

Driver Airbag (DAB) Module and Clock Spring Description and Operation

Description
•
The Driver Airbag (DAB) module is installed on the steering wheel and is electrically connected to the SRS Control Module (SRSCM) via the clock spring. In the event of a front collision, the airbag is deployed to protect the driver.
•
The clock spring is a device that transmits the operation signal generated from the sensors installed on the front and side of the vehicle to the inflator (gas generator) of the airbag module via the internal cable. It also transmits the steering wheel remote control switch and horn operation signals to the system via the internal cable.
Warning    
Direct measuring the resistance of the airbag module is very dangerous as it can cause the airbag deployment.
Note    
If the airbag is deployed due to an accident, the clock spring cannot be repaired or reused because there is a possibility of damage to the clock spring due to heat and impact caused by the explosion of the airbag module inflator (gas generating device). Be sure to replace with a new one.

Driver Airbag (DAB) Module and Clock Spring Troubleshooting

Troubleshooting
Airbag warning lamp on
The Clock Spring Repair Procedure

Restraint — Airbag Module / Driver Airbag (DAB) Module and Clock Spring / Troubleshooting illustration

Noise
The Clock Spring Repair Procedure

Restraint — Airbag Module / Driver Airbag (DAB) Module and Clock Spring / Troubleshooting illustration

Driver Airbag (DAB) Module and Clock Spring Removal

Removal
Driver Airbag (DAB)
1.
Disconnect the battery negative ( - ) terminal.
Note    
After disconnecting the battery negative ( - ) terminal, wait at least 3 minutes and 30 seconds.
2.
Remove the driver airbag module by pressing the fastening pin using the service hole (A) on the back of the steering wheel.

Restraint — Airbag Module / Driver Airbag (DAB) Module and Clock Spring / Removal illustration

3.
Remove the driver airbag module (A).

Restraint — Airbag Module / Driver Airbag (DAB) Module and Clock Spring / Removal illustration

4.
Disconnect the airbag module connector(A) and the horn connector (B).

Restraint — Airbag Module / Driver Airbag (DAB) Module and Clock Spring / Removal illustration

Clock Spring
1.
Disconnect the battery negative ( - ) terminal.
Note    
After disconnecting the battery negative ( - ) terminal, wait at least 3 minutes and 30 seconds.
2.
Remove the steering wheel.
(Refer to Steering System - "Steering Wheel")
3.
Remove the steering column shroud lower panel.
(Refer to Body - "Steering Column Shroud Panel")
4.
Disconnect the clock spring connectors (A).

Restraint — Airbag Module / Driver Airbag (DAB) Module and Clock Spring / Removal illustration

5.
Remove the clock spring (A) by releasing the fixing hook.

Restraint — Airbag Module / Driver Airbag (DAB) Module and Clock Spring / Removal illustration

Information    
Clip position :

Restraint — Airbag Module / Driver Airbag (DAB) Module and Clock Spring / Removal illustration

Driver Airbag (DAB) Module and Clock Spring Installation

Installation
1.
Set the clock spring in neutral position before assembling into the vehicle.
–
When the vehicle comes out of the factory, the clock spring is in a neutral state.
–
If the white cable is visible through the 7 o’clock neutral window of the vehicle, the clock spring is in neutral state.
–
If the white cable is not visible when checking through the 7 o’clock neutral window of the vehicle, adjust the setting to neutral manually.
Note    
If the clock spring is not set in neutral state, electric malfunctions such as airbag warning lamp on, horn, hands-free, auto cruise, heated wiring and heated steering, and noise from turning the steering may cause.
Neutral Check Window : Normal
Neutral Check Window : Fault

Restraint — Airbag Module / Driver Airbag (DAB) Module and Clock Spring / Installation illustration

Restraint — Airbag Module / Driver Airbag (DAB) Module and Clock Spring / Installation illustration

The white cable is visible through 7 O' Clock Neutral Check Window.
The white cable is not visible through 7 O' Clock Neutral Check Window.

2.
Clock spring manual neutral setting procedure.
(1)
Press the Auto Lock (A) at 6 o’clock and turn clockwise until the Auto Lock (A) stops.

Restraint — Airbag Module / Driver Airbag (DAB) Module and Clock Spring / Installation illustration

(2)
Press the 6 o'clock auto lock (A) and turn three times counterclockwise.
(3)
If the white cable is visible through the 7 o’clock neutral window of the vehicle, the clock spring is in neutral state.

Restraint — Airbag Module / Driver Airbag (DAB) Module and Clock Spring / Installation illustration

3.
Connect the clock spring wiring harness connector and horn wiring harness connector to the clock spring.
4.
Tighten the screw after installing the steering column shroud.
5.
Install the steering wheel.
(Refer to Steering System - "Steering Wheel")
6.
Install the airbag module.
–
When assembling the DAB module to the wheel, make sure that the airbag wire is not caught in the wheel's internal structure.
–
Assemble the airbag wire while pressing it toward the center of the module.
7.
After installing the airbag module, check if the airbag system and horn operates normally.
Note    
When IG is ON, the SRS indicator light should turn off after turning on for about 6 seconds.

Driver Airbag (DAB) Module and Clock Spring Inspection

Inspection
Airbag Module
Replace the airbag module with a new one when a problematic part is found during the inspection.
Caution    
Do not measure airbag module (ignition) circuit resistance even with the specified tester. If the circuit resistance is measured with a tester, the airbag deployment may cause serious injury.
1.
Check the airbag module for dents, cracks, or deformation.
2.
Check the hooks, connectors and terminals for damage, and harness bundles.
3.
Check the airbag inflator case for dents, cracks, or deformation.

Passenger Airbag (PAB) Module Description and Operation

Description
The passenger airbag (PAB) is installed inside the crash pad and protects the front passenger in the event of a frontal crash.
Warning    
Direct measuring the resistance of the airbag module is very dangerous as it can cause the airbag deployment.

Passenger Airbag (PAB) Module Troubleshooting

Troubleshooting

Restraint — Airbag Module / Passenger Airbag (PAB) Module / Troubleshooting illustration

Passenger Airbag (PAB) Module Removal and Installation

Removal
1.
Disconnect the battery negative ( - ) terminal.
Note    
After disconnecting the battery negative ( - ) terminal, wait at least 3 minutes and 30 seconds.
2.
Remove the main crash pad assembly.
(Refer to Body - "Main Crash Pad Assembly")
3.
Remove the passenger airbag module (A) after removing the bolts.

Tightening torque :
3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Restraint — Airbag Module / Passenger Airbag (PAB) Module / Removal and Installation / Removal illustration

Information    
Clip position :

Restraint — Airbag Module / Passenger Airbag (PAB) Module / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.
Note    
Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could lead to the malfunction of airbag system.
2.
After installing the airbag module, check if the airbag system operates normally.
Note    
When IG is ON, the SRS indicator light should turn off after turning on for about 6 seconds.

Side Airbag (SAB) module Description and Operation

Description
•
A Side Airbag (SAB) module is installed on the left and right sides of the driver’s seat back and on the right side of the front passenger’s seat back, and protects the occupants in the event of a side collision or rollover accident.
•
In the event of a side collision, the Side Impact Sensors (SIS) installed at the center of the left and right front door modules, the center pillar, and the left and right sides of the quarter panel detect the collision. The SRS Control Module (SRSCM) determines whether the side airbags (SAB) are deployed or not by using the signal from the sensors. In addition, when a vehicle rollover accident occurs, the SRSCM detects the vehicle rollover accident and determines whether to deploy the side airbags (SAB).
Warning    
Direct measuring the resistance of the airbag module is very dangerous as it can cause the airbag deployment.

Side Airbag (SAB) module Troubleshooting

Troubleshooting

Restraint — Airbag Module / Side Airbag (SAB) module / Troubleshooting illustration

Side Airbag (SAB) module Removal and Installation

Removal
Information    
Clip position :

Restraint — Airbag Module / Side Airbag (SAB) module / Removal and Installation / Removal illustration

1.
Disconnect the battery negative ( - ) terminal.
Note    
After disconnecting the battery negative ( - ) terminal, wait at least 3 minutes and 30 seconds.
2.
Remove the front seat back assembly from the front seat back frame.
(Refer to Body - "Front Seat Back Cover")
Note    
When replacing the airbag due to a deployment of the airbag, replace the seat back assembly.
3.
Remove the Side Airbag (SAB) (A) wiring clips (B).

Restraint — Airbag Module / Side Airbag (SAB) module / Removal and Installation / Removal illustration

4.
Remove the side airbag wiring mounting clips.

Restraint — Airbag Module / Side Airbag (SAB) module / Removal and Installation / Removal illustration

5.
Remove the side airbag (A) after removing the nuts.

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Restraint — Airbag Module / Side Airbag (SAB) module / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.
Note    
•
Incorrect installation of the front seat back cover blocks the normal deployment of the Side Airbags (SAB), so make sure that the front seat back cover is properly installed.
•
Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could lead to the malfunction of airbag system.
2.
After installing the airbag module, check if the airbag system operates normally.
Note    
When IG is ON, the SRS indicator light should turn off after turning on for about 6 seconds.

Curtain Airbag (CAB) Module Description and Operation

Description
•
The Curtain Airbag (CAB) module is built-in on the left and right side of the roof trim, and protects the occupants in the event of a side collision or rollover accident.
•
In the event of a side collision, the Acceleration type Side Impact Sensor (A-SIS), Pressure type Side Impact Sensor (P-SIS) installed at the center of the left and right front door modules, the center pillar, and the left and right sides of the detect the collision. The Supplemental Restraint System Control Module (SRSCM) determines whether the Curtain Airbags (CAB) are deployed or not by using the signal from the sensors. In addition, when a vehicle rollover accident occurs, the SRSCM detects the vehicle rollover accident and determines whether to deploy the Curtain Airbags (CAB).
Warning    
Direct measuring the resistance of the airbag module is very dangerous as it can cause the airbag deployment.

Curtain Airbag (CAB) Module Troubleshooting

Troubleshooting

Restraint — Airbag Module / Curtain Airbag (CAB) Module / Troubleshooting illustration

Curtain Airbag (CAB) Module Removal and Installation

Removal
1.
Disconnect the battery negative ( - ) terminal.
Note    
After disconnecting the battery negative ( - ) terminal, wait at least 3 minutes and 30 seconds.
2.
Remove the roof trim.
(Refer to Body - "Roof Trim Assembly")
3.
Disconnect the curtain airbag module connector (A).

Restraint — Airbag Module / Curtain Airbag (CAB) Module / Removal and Installation / Removal illustration

4.
Remove the curtain airbag module (A) after removing the bolts and clip.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Restraint — Airbag Module / Curtain Airbag (CAB) Module / Removal and Installation / Removal illustration

Information    
Clip position :

Restraint — Airbag Module / Curtain Airbag (CAB) Module / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.
Note    
•
Use the color of sentence and line on a module to identify curtain airbag.
–
Left side : Yellow label (attached to plastic cover)
–
Right side : Orange label (attached to plastic cover)
•
Be careful not to twist when the curtain airbag module installing. The curtain airbag module may not deploy normally if twisted.
•
Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could lead to the malfunction of airbag system.
2.
After installing the airbag module, check if the airbag system operates normally.
Note    
When IG is ON, the SRS indicator light should turn off after turning on for about 6 seconds.

Airbag Module Disposal Procedure ➤

Other information:

Kia Seltos SP2 (2021-2026) Service Manual: LCD display modes

You can switch between LCD display modes by pressing the Mode button. The available screens may differ depending on the Kia Seltos trim level, equipment, and active vehicle systems. Mode Driving Assist Trip Computer Tu

Kia Seltos SP2 (2021-2026) Service Manual: Cruise Control (CC)

Cruise indicator Set speed Cruise Control allows the Kia Seltos to maintain a selected speed above 20 mph (30 km/h) without the driver continuously pressing the accelerator pedal. It is most useful on open roads or highways with steady traffic flow.