Kia Seltos: Restraint / SRSCM
Contents:
- Components and Components Location
- On Vehicle Inspection
- SRS Control Module (SRSCM) Description and Operation
- SRS Control Module (SRSCM) Connector And Terminal Function
- SRS Control Module (SRSCM) Removal
- SRS Control Module (SRSCM) Installation
- Front Impact Sensor (FIS) Description and Operation
- Front Impact Sensor (FIS) Removal and Installation
- Side Impact Sensor (SIS) Description and Operation
- Side Impact Sensor (SIS) Removal and Installation
- Occupant Detecting System (ODS) Description and Operation
- Occupant Detecting System (ODS) Removal
- Occupant Detecting System (ODS) Installation
Components and Components Location
| Component |

| 1. Supplemental Restraint System Control Module
(SRSCM) 2. Pressure type Side Impact Sensor (P-SIS) |
3. Acceleration type Side Impact Sensor (A-SIS) 4. Front Impact Sensor (FIS) |
On Vehicle Inspection
| On Vehicle Inspection |
| Diagnosis with KDS |
| 1. |
The airbag system can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
|
SRS Control Module (SRSCM) Description and Operation
| Description |
| • |
The Supplemental Restraint System Control Module (SRSCM) determines whether and when to deploy the airbag
module and the seat Belt Pretensioner (BPT).
|
| • |
It supplies the power required for deployment at the time of deployment of the airbag module or seat Belt
Pretensioner (BPT).
|
| • |
It also performs the self-diagnosis function of Supplemental Restraint System (SRS).
|
SRS Control Module (SRSCM) Connector And Terminal Function
| Connector And Terminal Function |

|
Pin No |
Connector A |
Connector B |
|
1 |
IG 1 |
Ground ( - ) |
|
2 |
Driver's side front impact sensor (High) |
Driver's side seat belt pretensioner (High) |
|
3 |
Driver's side front impact sensor (Low) |
Driver's side seat belt pretensioner (Low) |
|
4 |
Driver airbag #1 (High) |
Driver's side belt anchor pretensioner (Low) |
|
5 |
Driver airbag #1 (Low) |
Driver's side belt anchor pretensioner (High) |
|
6 |
Passenger airbag #1 (Low) |
Driver's side airbag (High) |
|
7 |
Passenger airbag #1 (High) |
Driver's side airbag (Low) |
|
8 |
- |
Passenger's side airbag (Low) |
|
9 |
- |
Passenger's side airbag (High) |
|
10 |
Crash signal output |
Driver's side side impact sensor (High) |
|
11 |
Passenger's side front impact sensor (High) |
Driver's side side impact sensor (Low) |
|
12 |
Passenger's side front impact sensor (Low) |
Passenger's side side impact sensor (Low) |
|
13 |
Driver airbag #2 (High) |
Passenger's side side impact sensor (High) |
|
14 |
Driver airbag #2 (Low) |
Passenger's side seat belt buckle sensor (High) |
|
15 |
Passenger airbag #2 (Low) |
Passenger's side seat belt pretensioner (High) |
|
16 |
Passenger airbag #2 (High) |
Passenger's side seat belt pretensioner (Low) |
|
17 |
P-CAN (High) |
Passenger's side seat belt anchor pretensioner (Low) |
|
18 |
P-CAN (Low) |
Passenger's side seat belt anchor pretensioner (High) |
|
19 |
Battery ( + )(KL30) |
Driver's side curtain airbag (High) |
|
20 |
Passenger's side airbag OFF lamp (Telltale) |
Driver's side curtain airbag (Low) |
|
21 |
- |
Passenger's side curtain airbag (Low) |
|
22 |
- |
Passenger's side curtain airbag (High) |
|
23 |
- |
Driver's side door side impact sensor (High) |
|
24 |
Passenger airbag #3 vent (Low) |
Driver's side door side impact sensor (Low) |
|
25 |
Passenger airbag #3 vent (High) |
Passenger's side door side impact sensor (Low) |
|
26 |
C-CAN (High) |
Passenger's side door side impact sensor (High) |
|
27 |
C-CAN (Low) |
- |
|
28 |
Passenger's side rear seat belt retractor pretensioner (High) |
|
|
29 |
Passenger's side rear seat belt retractor pretensioner (Low) |
|
|
30 |
Driver's side rear seat belt retractor pretensioner (Low) |
|
|
31 |
Driver's side rear seat belt retractor pretensioner (High) |
|
|
32 |
- |
|
|
33 |
- |
|
|
34 |
- |
|
|
35 |
- |
|
|
36 |
- |
|
|
37 |
- |
|
|
38 |
- |
|
|
39 |
- |
SRS Control Module (SRSCM) Removal
| Removal |
| 1. |
Disconnect the battery negative ( - ) terminal.
|
| 2. |
Remove the floor console assembly.
(Refer to Body - "Floor Console Assembly")
|
| 3. |
Remove the rear air duct (A).
|
| 4. |
Disconnect the supplemental restraint system control module connectors (A) by pulling the connector lock
lever.
|
| 5. |
Remove the supplemental restraint system control module (A) after removing the bolts.
|
SRS Control Module (SRSCM) Installation
| Installation |
| 1. |
Install in reverse order of removal.
|
| 2. |
After installing the SRSCM, make sure that the airbag system operates normally.
|
| 3. |
When replaced the Supplemental Restraint System Control Module (SRSCM) perform the "ACU Variant Coding"
with the KDS.
(S/W Management → Airbag → ACU Variant Coding)
|
Front Impact Sensor (FIS) Description and Operation
| Description |
| • |
One Front Impact Sensor (FIS) is installed on the each of left and right sides of the engine room at the
top of the Front End Module
|
| • |
When event of a head-on collision, the Supplemental Restraint System Control Module (SRSCM) uses the
front impact sensor (FIS) signal to determine whether and when to deploy the Driver Airbag (DAB), front
Passenger Airbag (PAB), and seat Belt Pretensioner (BPT).
|
Front Impact Sensor (FIS) Removal and Installation
| Removal |
| 1. |
Disconnect the battery negative ( - ) terminal.
|
| 2. |
Disconnect the front impact sensor connector (A).
|
| 3. |
Remove the front impact sensor (A) after removing the nut.
|
| Installation |
| 1. |
Install in reverse order of removal.
|
| 2. |
After installing the front impact sensor, make sure that the system operates normally.
|
Side Impact Sensor (SIS) Description and Operation
| Description |
| • |
The Side Impact Sensor (SIS) is installed one each at the center of the left and right front door modules
and near the left and right center pillars to detect side collisions of the vehicle.
|
| • |
The SIS consists of the Pressure type Front Side Impact Sensor sensing the collision pressure, the
Acceleration type Front Side Impact Sensor sensing the front side collision acceleration.
|
| • |
In the event of a side collision, the Supplemental Restraint System Control Module (SRSCM) determines
whether and when to deploy the Side Airbag (SAB) module by using the side collision detection sensor signal.
|
Side Impact Sensor (SIS) Removal and Installation
| Removal |
Pressure type Side Impact Sensor (P-SIS)
| 1. |
Disconnect the battery negative ( - ) terminal.
|
| 2. |
Remove the front door trim.
(Refer to Body - "Front Door Trim")
|
| 3. |
Disconnect the pressure type side impact sensor (P-SIS) connector (A).
|
| 4. |
Remove the pressure type side impact sensor (P-SIS) (A) by turning it in the direction of the arrow.
|
Acceleration type Side Impact Sensor
| 1. |
Disconnect the battery negative ( - ) terminal.
|
| 2. |
Remove the center pillar lower trim.
(Refer to Body - "Center Pillar Trim")
|
| 3. |
Disconnect the acceleration type side impact sensor (A-SIS) connector (A).
|
| 4. |
Remove the acceleration type side impact sensor (A-SIS) (A) after removing the bolt.
|
| Installation |
| 1. |
Install in reverse order of removal.
|
| 2. |
After installing the sensor, make sure that the system operates normally.
|
Occupant Detecting System (ODS) Description and Operation
| Description |
| • |
For normal operation of the passenger side airbag, the Supplemental Restraint System Control Module
(SRSCM) detects a Diagnostic Trouble Code (DTC) of the occupant detective system unit.
|
| • |
The Occupant Detective System (ODS) sensor mounted on the passenger seat divides the passenger into a
child protection device and an adult and sends passenger information to the SRSCM.
|
| • |
The SRSCM decides whether the Passenger Airbag (PAB) deploys by using the passenger information and crash
signal.
|
Occupant Detecting System (ODS) Removal
| Removal |
| [Occupant Detection System Mat] |
| 1. |
Remove the passenger side front seat cushion pad (A).
(Refer to Body - "Front Seat Cushion Cover")
|
| [Occupant Detection System Unit] |
| 1. |
Remove the passenger side front seat assembly.
(Refer to Body - "Front Seat Assembly")
|
| 2. |
Disconnect the occupant detection system unit connector (A).
|
| 3. |
Disconnect the seat heating and ventilation unit connectors (A).
|
| 4. |
Remove the occupant detection system unit bracket (A) after removing the screws.
|
| 5. |
Remove the occupant detection system unit (A) after removing the screws.
|
Occupant Detecting System (ODS) Installation
| Installation |
Occupant Detective System (ODS)
| 1. |
Install in reverse order of removal.
|
Occupant Detective Sensor Initialization
| 1. |
Perform the occupant detective sensor initialization wite the KDS.
(S/W Management → Occupant Detective Sensor → Body Sensor Reset)
|




















