Kia Seltos SP2 (2021-2026) Service Manual / Body (Interior and Exterior) / Windshield Glass
Kia Seltos: Body (Interior and Exterior) / Windshield Glass
Contents:
Removal and Installation
| Removal |
| 1. |
Remove the front pillar trim.
(Refer to Interior Trim - "Front Pillar Trim")
|
| 2. |
Remove the inside rear view mirror assembly.
(Refer to Mirror - "Inside Rear View Mirror")
|
| 3. |
Remove the auto defogging sensor.
(Refer to Heater and Air Conditioning Unit - "Auto Defogging
Sensor")
|
| 4. |
Remove the rain sensor.
(Refer to Body Electrical System - "Rain Sensor")
|
| 5. |
Remove the front view camera unit.
(Refer to Advanced Driver Assistance Systems (ADAS) - "Front
Camera")
|
| 6. |
Remove the cowl top cover.
(Refer to Cowl Top Cover - "Removal and Installation")
|
| 7. |
Remove the A pillar garnish.
(Refer to Body Side Molding - "A Pillar Garnish")
|
| 8. |
Insert the piano wire (A) in the corner side.
|
| 9. |
While pulling the piano wire (A) in the direction of the arrow, cut out the sealant on the front edge
side (B).
|
| 10. |
Cut the sealant in sections (A-A) and (B-B) while pulling the piano wire left and right.
|
| 11. |
Cut the sealant in section (A-A) using a cutter knife.
|
| 12. |
Carefully remove the windshield glass (A) using the glass holder (B).
|
| 13. |
Remove the glass molding (A) using a cutter knife.
|
| Installation |
When replacing with the windshield glass of the front camera type, be sure to replace with the type
equipped with the coupler. If the coupler is attached to the windshield glass type that is not equipped with
the coupler, the front camera may not work properly.
|
| 1. |
Cut off leaving about 2 mm (0.079 in.) thick sealant at the bonding surface around the body panel by
using a cutter knife. Marking the glass and body if a new windshield glass is used.
|
| 2. |
Clean the edges of the body panel and the windshield glass with alcohol, etc.
|
| 3. |
Apply the body primer to the edge of the body panel (A).
|
| 4. |
Apply a body primer to the edge of the body panel.
|
| 5. |
Attach the glass molding (A) to the windshield glass.
|
| 6. |
Apply the sealant (B) around the windshield glass (A) using the sealant.
|
| 7. |
Align the windshield glass (A) with the stopper hole (B) of the body using a glass holder and press the
windshield glass to the body flange surface by carefully tapping.
|
| 8. |
Test for water leakage.
|
| 9. |
If water leak occurs, apply sealant to the leak area.
|
| 10. |
Install the front view camera.
(Refer to Advanced Driver Assistance Systems (ADAS) - "Front
Camera")
|
| 11. |
Install the rain sensor.
(Refer to Body Electrical System - "Rain Sensor")
|
| 12. |
Install the auto defogging sensor.
(Refer to Heater and Air Conditioning Unit - "Auto Defogging
Sensor")
|
| 13. |
Install the inside rear view mirror assembly.
(Refer to Mirror - "Inside Rear View Mirror")
|
| 14. |
Install the front pillar trim.
(Refer to Interior Trim - "Front Pillar Trim")
|
| 15. |
Install the A pillar garnish.
(Refer to Body Side Molding - "A Pillar Garnish")
|
| 16. |
Install the cowl top cover.
(Refer to Cowl Top Cover - "Removal and Installation")
|
Other information:
Kia Seltos SP2 (2021-2026) Service Manual: User Settings mode
In the Kia Seltos User Settings mode, you can customize several vehicle functions directly through the instrument cluster. This menu allows the driver to adjust cluster preferences, lighting behavior, door functions, convenience features, units, language, and reset options. Driver Assistance Cluster Lights Door Convenience Units Language Reset The available information and settings may differ depending on the systems and equipment installed in your Kia Seltos.


