Owner's library Kia Seltos Manuals Owner's manual pages, service notes, maintenance references and practical Kia Seltos help in one clean library.

Kia Seltos reference pages

Manuals, maintenance notes and quick owner help.

Find Kia Seltos operating instructions, warning light explanations, service information and owner guidance without digging through a full PDF.

Kia Seltos: Body Electrical System / Wiper/Washer

Contents:

Wiper Arm Removal and Installation

Removal
Front Wiper Arm
1.
Remove the wiper arms (A) by removing the nuts after removing the caps.

Tightening torque :
22.6 - 26.5 N·m (2.3 - 2.7 kgf·m, 16.6 - 19.5 lb·ft.)

Body Electrical System — Wiper/Washer / Wiper Arm / Removal and Installation / Removal illustration

Rear Wiper Arm
1.
Separate the rear wiper arm cap (A) by pulling in the direction of the arrow.

Body Electrical System — Wiper/Washer / Wiper Arm / Removal and Installation / Removal illustration

2.
Remove the rear wiper arm (A) after removing the nut.

Tightening torque :
3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Body Electrical System — Wiper/Washer / Wiper Arm / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.
Note    
•
When installing, place the wiper arm to the specified position and then tighten the nut.
[Front Wiper]
–
Place the wipers to the marking (A) position of cowl top cover.

Body Electrical System — Wiper/Washer / Wiper Arm / Removal and Installation / Installation illustration

–
Place the wipers to the marking (A) position of windshield glass.

Body Electrical System — Wiper/Washer / Wiper Arm / Removal and Installation / Installation illustration

Wiper Motor Terminal Function

Connector and Terminal Function
[Front Wiper Motor]

Body Electrical System — Wiper/Washer / Wiper Motor / Terminal Function / Connector and Terminal Function illustration

Connector A
Terminal
Function

Body Electrical System — Wiper/Washer / Wiper Motor / Terminal Function / Connector and Terminal Function illustration

1
Front wiper (High)
2
Front wiper (Low)
3
Battery (+)
4
Front wiper (Parking)
5
Ground

[Rear Wiper Motor]

Body Electrical System — Wiper/Washer / Wiper Motor / Terminal Function / Connector and Terminal Function illustration

Connector A
Terminal
Function

Body Electrical System — Wiper/Washer / Wiper Motor / Terminal Function / Connector and Terminal Function illustration

1
Rear wiper (Low)
2
Ground
3
Rear wiper (Parking)

Wiper Motor Removal and Installation

Removal
Front Wiper Motor
1.
Disconnect the negative ( - ) battery terminal.
2.
Remove the cowl top cover.
(Refer to Body - "Cowl Top Cover")
3.
Disconnect the wiper motor connector (A).

Body Electrical System — Wiper/Washer / Wiper Motor / Removal and Installation / Removal illustration

4.
Remove the wiper motor (A) after removing the bolts.

Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft.)

Body Electrical System — Wiper/Washer / Wiper Motor / Removal and Installation / Removal illustration

Rear Wiper Motor
1.
Remove the rear wiper arm.
(Refer to Wiper/Washer - "Wiper Arm")
2.
Remove the tailgate lid lower trim.
(Refer to Body - "Tailgate Lid Trim")
3.
Disconnect the rear wiper motor connector (A).

Body Electrical System — Wiper/Washer / Wiper Motor / Removal and Installation / Removal illustration

4.
Remove the rear wiper motor (A) after removing the bolts.

Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft.)

Body Electrical System — Wiper/Washer / Wiper Motor / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.

Washer Motor Removal and Installation

Removal
Washer Motor
1.
Disconnect the negative ( - ) battery terminal.
2.
Remove the engine room under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
3.
Disconnect the washer motor connector (A).

Body Electrical System — Wiper/Washer / Washer Motor / Removal and Installation / Removal illustration

4.
Remove the washer motor (A) in the direction of the arrow after separating the washer nozzle hoses (B).

Body Electrical System — Wiper/Washer / Washer Motor / Removal and Installation / Removal illustration

Note    
Washer fluid is drained when removing washer motor.
Washer Fluid Level Sensor
1.
Disconnect the negative ( - ) battery terminal.
2.
Remove the engine room under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
3.
Disconnect the washer fluid level sensor connector (A).

Body Electrical System — Wiper/Washer / Washer Motor / Removal and Installation / Removal illustration

4.
Remove the washer level sensor (A) in the direction of the arrow.

Body Electrical System — Wiper/Washer / Washer Motor / Removal and Installation / Removal illustration

Reservoir tank
1.
Remove the engine room under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
2.
Remove the front wheel guard [Passenger's side].
(Refer to Body - "Front Wheel Guard")
3.
Disconnect the washer motor connector (A).

Body Electrical System — Wiper/Washer / Washer Motor / Removal and Installation / Removal illustration

4.
Disconnect the washer fluid level sensor connector (A).

Body Electrical System — Wiper/Washer / Washer Motor / Removal and Installation / Removal illustration

5.
Remove the wiring clips (A), (B).

Body Electrical System — Wiper/Washer / Washer Motor / Removal and Installation / Removal illustration

6.
Separate the washer nozzle hoses (A).

Body Electrical System — Wiper/Washer / Washer Motor / Removal and Installation / Removal illustration

7.
Remove the reservoir tank (A) after removing the bolts.

Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8 lb·ft.)

Body Electrical System — Wiper/Washer / Washer Motor / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.

Washer Motor Inspection

Inspection
Washer Motor
1.
Before filling the reservoir tank with water, check the filter for foreign material or contamination.
→ Clean the filter if necessary
Note    
Using low-grade washer fluid may clog the washer pump and cause the malfunction of the pump motor.
2.
Fill the washer fluid after installing the washer motor in the reservoir tank.
3.
Connect terminal 1 to the battery ( - ) terminal and sequentially connect terminals 2 and 3 to the battery ( + ) terminal.
4.
Check the washer motor operates normally and water sprays from the washer nozzles.
5.
If they are abnormal, replace the washer motor.

Body Electrical System — Wiper/Washer / Washer Motor / Inspection illustration

Terminal
Function
1
Ground
2
Washer ( + )
3
Rear Washer ( + )

Washer Fluid Level Sensor
1.
Disconnect the negative ( - ) battery terminal.
2.
Drain the washer fluid less than 650 cc.
3.
Check the continuity of between terminals.

Body Electrical System — Wiper/Washer / Washer Motor / Inspection illustration

Body Electrical System — Wiper/Washer / Washer Motor / Inspection illustration

Rain Sensor Terminal Function

Connector and Terminal Function

Body Electrical System — Wiper/Washer / Rain Sensor / Terminal Function / Connector and Terminal Function illustration

Connector A
Terminal
Function

Body Electrical System — Wiper/Washer / Rain Sensor / Terminal Function / Connector and Terminal Function illustration

1
Battery (+)
2
Ground
3
LIN

Rain Sensor Removal

Removal
Note    
•
Do not damage or touch the silicone.
•
Be careful so that the silicon is not contaminated by foreign substances, dust, etc.
•
Use caution, as the silicon may be damaged if you try to separate the rain sensor using force.
Information    
•
The dust or foreign substance on the rain sensor may have bad influence on the performance of the rain sensor. In order to ensure accurate function of the rain sensor, protect the sensor surface with the protection cover until the sensor is installed on the bracket.
•
The coupling pad on the rain sensor surface is adhesive and the coupling pad may stick to the windshield during the use depending on the environment condition. Therefore, it may be damaged when you try to remove the rain sensor from the windshield if using force. Use caution when separating it from the windshield.
1.
Disconnect the negative ( - ) battery terminal.
2.
Remove the multi sensor blanking cover (A).

Body Electrical System — Wiper/Washer / Rain Sensor / Removal illustration

Body Electrical System — Wiper/Washer / Rain Sensor / Removal illustration

Information    
Clip position :

Body Electrical System — Wiper/Washer / Rain Sensor / Removal illustration

3.
Remove the multi sensor cover (A) in the direction of the arrow.

Body Electrical System — Wiper/Washer / Rain Sensor / Removal illustration

Body Electrical System — Wiper/Washer / Rain Sensor / Removal illustration

Information    
Clip position :

Body Electrical System — Wiper/Washer / Rain Sensor / Removal illustration

4.
Disconnect the rain sensor connector (A).

Body Electrical System — Wiper/Washer / Rain Sensor / Removal illustration

5.
Remove the rain sensor.
(1)
Separate both clips (B) of the rain sensor in the direction of the arrows by using the flat-blade screwdriver.
(2)
Remove the rain sensor (A) from the windshield glass.

Body Electrical System — Wiper/Washer / Rain Sensor / Removal illustration

Note    
•
Sensor may be damaged when you try to remove the rain sensor from the windshield using force. Use caution when separating it from the windshield.
•
When detaching the silicone under a high temperature, it may be easily damaged because of the adhesive strength of the silicone. Remove the silicone in a cool environment.

Body Electrical System — Wiper/Washer / Rain Sensor / Removal illustration

Silicone Pad Reuse Criteria After Rain Sensor Removal and Installation Precautions (Play ▶)Body Electrical System — Wiper/Washer / Rain Sensor / Removal illustration
Notes When Refering Video
This video provides guidance for understanding complex or hard-to-follow procedures by showing each step clearly.
As needed, the video also provides clear guidance on essential procedural steps, including adjustment and diagnostic processes, the use of SSTs, and precautions to avoid component damage.
•
This video is created using common specifications and may differ from the actual vehicle.
•
The location and repair procedures of the parts may vary depending on vehicle model, model year, region, and specifications.
•
Check the KDS guide for detailed information on how to use the KDS.
•
Check the manual for detailed maintenance procedures.
•
Unauthorized reproduction, distribution, or sharing of this video is prohibited.

Rain Sensor Installation

Installation
1.
Install in reverse order of removal.
Note    
•
When installing the rain sensor, do not fix it by pressing both spring arms (A) at the same time.
•
An incorrectly mounted snap connection may cause malfunctions of the rain/light sensor.

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration

Information    
•
Check the operation of the rain sensor and the light sensor before mounting.
–
Check the sensor for silicon damage.
–
Check whether the rain sensor connector is tightened.
–
Check whether the rain sensor and bracket are properly tightened.
–
Check whether the sensor mounted area is free from foreign matters.
–
Recalibrate sensitivity of the switch if the auto-wiping operation is having too little or too much sensitivity.

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration

•
In case the silicone of the rain sensor is normal or slightly damaged as shown in the images below, it can be reused.
Normal
Damage within 1.5 mm of outer part

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration


•
In case the silicone of the rain sensor is damaged as shown in the below images, it should be replaced with a new silicone.
Damage
Fingerprint
Damage

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration


Damage

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration


•
If the rain sensor silicone is damaged, replace it as follows.
1)
Remove the damaged silicone gel pad from the lens plate completely.

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration

Note    
Be careful not to damage or contaminate the surface of the lens plate during removal.
2)
Attach the new silicone gel pad after removing the silicone paper then remove the transparent film.

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration

Note    
When attaching the silicone gel pad to the sensor, be careful not to contaminate.
•
It is very important that the silicon (coupling pad) is completely pushed against the windshield and stuck without any air bubble.

Body Electrical System — Wiper/Washer / Rain Sensor / Installation illustration

•
In case of replacing the damaged windshield, you may reuse the undamaged existing rain sensor.
•
The windshield glass has to be clean and free of contamination or foreign substances.

Wiper Blade Replacement

Replacement
Front Wiper Blade
Information    
•
After turning off the engine, move the wiper switch to the single wiping (MIST) position within 20 seconds and hold the switch more than 2 seconds until the wiper blade is in the service position.
•
After IG ON, move the wiper switch to the single wiping (MIST) and wiper arms will return to the normal operating position.
1.
Remove the blade by pushing it in the direction of the arrow after opening the hook (A).

Body Electrical System — Wiper/Washer / Wiper Blade / Replacement illustration

2.
Install in reverse order of removal.
Rear Wiper Blade
1.
Remove the blade (A) by pulling it in the direction arrow after opening the hook.

Body Electrical System — Wiper/Washer / Wiper Blade / Replacement illustration

2.
Install in reverse order of removal.

Other information:

Kia Seltos SP2 (2021-2026) Service Manual: Exterior care

Use the following information to maintain the exterior of your Kia Seltos. Keeping the exterior clean is not only visually pleasing, but also helps protect paint, trim, lamps, and body components from wear, contamination, and environmental damage. NOTICE If the Kia Seltos is parked near a stainless signboard, glass building, or other highly reflective structure, reflected sunlight may damage plastic exterior trim such as the bumper, spoiler, trim pieces, lamps, or outside mirrors.

Kia Seltos SP2 (2021-2026) Service Manual: Vehicle load limit

The vehicle load limit for the Kia Seltos is shown on the tire and loading information label located on the driver's door area. Tire and loading information label The label on the driver's door sill shows the original tire size, the recommended cold tire pressures, the maximum number of occupants, and the vehicle capacity weight for your Kia Seltos.