Kia Seltos SP2 (2021-2026) Service Manual / Suspension System / Alignment
Kia Seltos: Suspension System / Alignment
Contents:
Description and Operation
| Description |
| • |
Wheel alignment is all forces due to friction, gravity, centrifugal force and inertia operate in a
balanced manner while driving.
|
| • |
Wheel alignment improves linearity, grounding performance, tire life extension and fuel reduction and
ensures safety at high speeds.
|
| • |
Alignment adjustments consist of camber, castor, kingpin angle, toe, left, thrust angle, etc.
|
| Components |
Camber
Camber refers to the angle at which the top of the wheel is tilted inward or outward relative to the vertical
line started from the center of the floor when the vehicle is viewed from the front.
| – |
It facilitates steering control of the steering wheel and prevents bending of the front axle.
|
( + ) Camber
It is a camber form with wheels tilted outward from the top. It prevents the underside of the wheel from opening,
so there is less tire wear due to unnecessary driving resistance on curves.

( - ) Camber
It is a camber form with wheels tilted inward from the top. cause strong friction when driving curves but tires
are prone to wear.

Caster
Caster refers to the angle at which the steering shaft tilts forward and backward relative to the vertical line
initiated from the center of the wheel floor when the vehicle is viewed from the side.
| – |
It gives a straight line to the steering wheel when driving.
|
| – |
Provides resilience to wheels when steering.
|
| – |
It prevents shaking of wheels while driving.
|

King pin angle
Kingpin angle refers to the angle at which the centerline of the steering shaft and the bottom vertical line
forms when the vehicle is viewed from the front.
| – |
Provides easy steering of the steering wheel and resilience of the steering wheel.
|
| – |
The kingpin angle and camber are also called Included Angle (I.A.). [Included Angle (I.A.)]
|

|
Item |
Description |
|
A |
Strut centerline |
|
B |
King pin angle |
|
C |
Centerline |
Toe
Toe is the tilted angle or distance at the front of the wheel when looking up and down at the vehicle.
| – |
The state in which the front of the wheel faces outward is called Toe out, and the state in which the
front of the wheel faces inward is called Toe in.
|
| – |
In general vehicles, toe-in is applied to prevent side slip.
※ Side slip: A phenomenon in which the wheels slide sideways due to the influence of the camber while the
vehicle is driving.
|
| – |
Toe-out is sometimes applied to vehicles that require a fast steering response when turning.
|

Set Back
Set back refers to the angle at which the line connects the center of the front wheels from the vehicle's
centerline.
| – |
The main cause of the set back is the presence of an accident in the vehicle or an abnormality in the
body.
|

Thrust angle
The angle at which the Thrust line and the centerline of the vehicle are formed.
※Thrust line: A line that is perpendicular to the center line of the vehicle and the center line of the rear
axle.
| – |
Thrust conditions occur when the rear wheel individual toe is not the same.
|

Poor thrust angles can increase tire wear, reduce steering direction, and cause dog tracking.
※Dog tracking: The driving condition when the thrust line is not parallel to the center line of the
vehicle
|
On Vehicle Inspection
| On Vehicle Inspection |
Driving Test
Carry out pre-work vehicle driving tests to check vehicle behavior under normal driving conditions.
| On straight, flat road |
| 1) |
Check that the vehicle is going straight when release the steering wheel.
|
| Stop and Go |
| 1) |
Check that the vehicle pulls to one side while accelerating and braking.
|
| Turning left or right |
| 1) |
Check whether the vehicle is restored to a straight line when released the steering wheel after turning.
|
Tire Wear Inspection
| Wheel and tire diagnosis |
||||||||||||||||||||||||||
|
Rapid wear at the center |
Rapid wear at both shoulders |
Wear at one shoulder |
||||||||||||||||||||||||
|
|
|
|
||||||||||||||||||||||||
|
|
|
||||||||||||||||||||||||
|
Partial wear |
Feathered edge |
Wear pattern |
||||||||||||||||||||||||
|
|
|
|
||||||||||||||||||||||||
|
|
|
||||||||||||||||||||||||
Inspect steering system related parts
| 1) |
Check the steering gear box for damage or installed firmly.
|
| 2) |
Check the tie rod end ball joint for damage or free play.
|
Inspect suspension system related parts
| 1) |
Check each suspension bushing for wear, cracks, etc.
|
| 2) |
Check the strut and shock absorber for damage.
|
| 3) |
Check the ride height
|
| 4) |
Check the coil spring for damage or wear.
|
| 5) |
Check the lower arm ball joint for damage or free play.
|
Repair procedures
| Wheel Alignment Repair Procedures |
| 1. |
When using the wheel alignment tester to check the wheel alignment, align the lift's vehicles
horizontally.
|
| 2. |
Set the transmission gear to 'N'.
|
| 3. |
Inflate the 4 tires to the specified tire pressure.
Tire Pressure
|
||||||||||||||||
| 4. |
Align the steering wheel in a straight-ahead position using a digital level or other equivalent tools.
|
| 5. |
Hold the brake pedal depressed using a pedal stopper.
|
| 6. |
Measure the ride height, which is the distance from the end of the fender to the center of the wheel.
|
| 7. |
Adjust the alignment.
(Refer to Alignment - "Adjust")
|
| 8. |
Shake the vehicle up and down after alignment adjustment.
|
| 9. |
After adjustment, perform the Steering Angle Sensor (SAS) Calibration using KDS.
(Refer to Steering System - "Steering Angle Sensor (SAS) Calibration")
|
Adjustment
| Adjustment |
[Rear - Multi Link]
It is not recommended to adjust the rear alignment of the coupled torsion beam axle type using an
adjustment shim or washer. Vehicle performance may be poor.
|
| Toe |
Turn the cam bolt (A) attached with the rear assist arm clockwise or counterclockwise to adjust the toe. Adjust
the left and right cam bolts to the same amount.
|
Total :
0.01° ± 0.2°
Individual :
0.005° ± 0.1°
|
|
Cam bolt |
Rotation |
Increae / Decrease |
|
RH |
Clockwise |
Toe-In |
|
LH |
Clockwise |
Toe-Out |

Adjust the toe using total toe.
|
| Camber |
Turn the cam bolts (A) attached with the rear lower arm clockwise or counterclockwise to adjust the camber.
|
Camber Angle :
-1.2 ± 0.5°
|
|
Cam bolt |
Rotation |
Increae / Decrease |
|
RH |
Clockwise |
+ Camber |
|
LH |
Clockwise |
- Camber |

| Thrust angle |
|
Thrust angle :
0° ± 0.15°
|

[Front]
| Toe |
Toe is adjusted by rotation of the tie rod rotation buckle. Turning the tie rod to the rear of the vehicle will
reduce the toe on the front wheels. The adjustment toe is adjusted by turning the left and right tie rods to the
same value.
|
Total :
0.12° ± 0.2°
Individual :
0.06° ± 0.1°
|

| 1. |
Loosen the tie rod end nut (A) until the toe can be adjusted.
|
| 2. |
Fix the tie rod end (A) with a wrench to prevent turning during adjustment.
|
| 3. |
Rotate the tie rod turn buckle (A) to adjust the toe to the specified value.
|
| 4. |
After adjustment, tighten the tie rod end nut (A) to specification torque.
|
|
| Camber |
The camber cannot be adjusted. If the measured camber exceeds the standard limit, repair or replace the relevant
parts and inspect the wheel alignment again.
|
Camber angle :
2WD : -0.5° ± 0.5°
4WD : -0.4° ± 0.5°
|

|
Item |
Description |
|
A |
Camber Angle |
|
B |
Center line |
| Caster |
The caster cannot be adjusted. If the measured caster exceeds the standard limit, repair or replace the relevant
parts and inspect the wheel alignment again.
|
Tire Size |
Drive Type |
Specification |
| 205/60 R16 |
2WD |
4.33 ± 0.5 |
|
4WD |
4.28 ± 0.5 |
|
| 215/55 R17 |
2WD |
4.34 ± 0.5 |
|
4WD |
4.29 ± 0.5 |
|
| 235/45 R18 |
2WD |
4.37 ± 0.5 |
|
4WD |
4.31 ± 0.5 |

|
| Kingpin |
The king pin angle cannot be adjusted. If the measured caster exceeds the standard limit, repair or replace the
relevant parts and inspect the wheel alignment again.
|
King ping angle :
2WD : 13.8° ± 0.5°
4WD : 13.6° ± 0.5°
|

|
Item |
Description |
|
A |
Strut center line |
|
B |
Kingpin |
|
C |
Center line |
| Set back |
The set back cannot be adjusted, but their values are useful for diagnosing steering problems, such as pull and
wander. After repairing a vehicle with a damaged frame, the set back must be checked. The ideal set back value
should be 0.

Other information:
Kia Seltos SP2 (2021-2026) Service Manual: Piston and Connecting Rod Inspection
Inspection The connecting rods. 1. Check the connecting rod side clearance. Using a feeler gauge, measure the end play while moving the connecting rod back and forth. • If out-of-tolerance, install a new connecting rod.Troubleshooting Failure Diagnosis 1. In principle, ESC and TCS controls are prohibited in case of ABS failure. 2. When ESC or TCS fails, only the failed system control is prohibited. 3.












