Kia Seltos SP2 (2021-2026) Service Manual / Suspension System / Wheel and Tire
Kia Seltos: Suspension System / Wheel and Tire
Contents:
- Tire Inspection
- Tire Removal
- Tire Installation
- Tire Replacement
- Wheel Removal and Installation
- Wheel Inspection
- Wheel Balance Description and Operation
- Wheel Balance Inspection
Tire Inspection
| Tire Wear |
| 1. |
Measure the tread depth of the tires.
|
| 2. |
If the remaining tread depth (A) is less than the limit, replace the tire.
|
Tire Removal
| Removal |
| 1. |
Remove the wheels and tires.
(Refer to Tires/Wheels - "Wheel")
|
| 2. |
Deflate the tires.
|
| 3. |
Remove the tire from the wheel using the tire replacing equipment.
|
| 4. |
Remove the tire by levering it and rotating the wheel clockwise.
|
Tire Installation
| Installation |
| 1. |
Lubricate the tire bead side using tire mounting lubricant.
|
| 2. |
Place the TPMS sensor at 5 o'clock position from the tire replacing machine head for installing the
bottom bead.
|
| 3. |
Rotate the rim clockwise, and push down on the tire at the 3 o’clock position to install the bottom bead.
|
| 4. |
Push down the tire at 3 o'clock position and then rotate the rim clockwise to install the upper bead.
|
| 5. |
Inflate the tire until the beads fit.
Tire Pressure
|
||||||||||||||
| 6. |
Install the wheels and tires.
(Refer to Tires/Wheels - "Wheel")
|
Tire Replacement
| Tire Rotation |
When directional or asymmetric tires applied, do not perform left/right or diagonal tire replacement.
Driving and braking performance may be poor which may affect safety.
|
Replace the tire in the direction shown by the arrow in the figure below.

Pre-inspection when the vehicle is pulling to one side
| 1. |
Inspect the tire pressure.
Tire pressure
|
||||||||||||||
| 2. |
Check the steering wheel off-center.
|
| 3. |
Check the wheel alignment.
(Refer to Alignment - "Repair Procedures")
|
Rotating For Pull And Wander
If there is no abnormality in the vehicle after a pre-inspection and the vehicle continues to pull to one side,
uneven tire wear may be the cause.
In this case, the following tire replacement procedures shall be performed.
| 1. |
Rotate the front right and front left tires, and perform a road test in order to confirm vehicle
stability.
|
| 2. |
If the steering pulls to the opposite side, rotate the front and rear tires, and perform a road test
again.
|
| 3. |
If the steering continues to pull to one side, rotate the front right and left tires again, and perform a
road test.
|
| 4. |
If the steering continues to pull to the opposite side, replace the front wheels with new ones.
|
Wheel Removal and Installation
| Removal |
| 1. |
Remove the wheel and tire (A).
[Front]
[Rear]
|
| Installation |
| 1. |
Install the wheel and tire (A).
[Front]
[Rear]
|
Wheel Inspection
| Wheel Run-out Inspection |
| 1. |
Jack up the vehicle and support with a jack securely.
|
| 2. |
Measure the wheel Run-out by using a dial indicator as illustration below.
|
||||||||
| 3. |
If measured value exceeds the standard value, replace the wheel.
|
Wheel Balance Description and Operation
| Description |
Symptoms of Defective Wheel Balance
| If the wheel balance is defective |
1. Steering wheel vibration occurs. |
|
2. Road impact is transmitted to the steering wheel during driving. |
|
|
3. Irregular tire wear occurs. |
|
|
4. Driving vibration decreases ride comfort. |
| Types of Wheel Imbalance |
|||||||||||||
| Symptoms of Defective Static Balance(If the tire weight is applied to only one side) |
Symptoms of Defective Dynamic Balance(If the tire weight is not applied equally to left and right
sides) |
||||||||||||
|
|
|
|
|
||||||||||
Types of Wheel Balance
|
|
Road Balancing |
Road Force Balancing |
||||||||||
|
|
If the imbalance symptoms occur due to defective wheel balance after road balancing, do road force
balancing. |
|||||||||||
|
Inspection and Adjustment Procedure |
|
|
||||||||||
|
Wheel balance equipment |
|
|
||||||||||
| • |
Road Balancing
|
| – |
Tire road balancing is a procedure to examine and adjust that the weight of the tire and wheel is equally
applied around the rotation axis during turning.
|
| – |
Do road balancing if tire wear is irregular, the steering wheel vibrates, or the tire is replaced.
|
| – |
If imbalance is caused by irregular weight distribution, install balance weight on the wheel to adjust
the weight.
|
| – |
If road balancing does not correct the problem, do road force balancing.
|
| • |
Road Force Balancing
|
| – |
Road force balancing is a accurate procedure that applies vertical load to the tire under conditions
equivalent to actual driving. It measures and adjusts imbalances caused by tire deformation and lateral
wobble that cannot be identified by standard balancing.
|
| – |
Do road force balancing if tire wear is irregular, the steering wheel vibrates, or the tire is replaced.
|
| – |
If imbalance is caused by unbalanced weight distribution, install the balance weight on the wheel at the
position marked by the red laser.
|
| – |
If road force balancing does not correct the problem, damage to the wheel or a tire defect can be
predicted.
|
Wheel Balance Inspection
| Inspection |
Wheel balance needs to be adjusted if the tires are unbalanced or after tire replacement or maintenance work has
been performed.
|
Maximum rim unbalance weight :
2.12 oz (60 g)
|

|
Other information:
Kia Seltos SP2 (2021-2026) Service Manual: If you have a flat tire (with spare tire)
If your Kia Seltos has a flat tire, it may be replaced with the spare tire by using the supplied tools. Always park the vehicle safely before beginning any tire change procedure. WARNING Driving the Kia Seltos on a flat tire can permanently damage the tire. Re-inflating a tire that has been driven while severely underinflated or completely flat may cause a blowout and could lead to a serious crash.Kia Seltos SP2 (2021-2026) Service Manual: Smart key immobilizer system
The Kia Seltos smart key immobilizer system helps protect the vehicle from theft. If an incorrectly coded key or an unauthorized electronic device is used, the vehicle's power system may be disabled and the engine may not start. When the ENGINE START/STOP button is placed in the ON position, the immobilizer system indicator should illuminate briefly and then turn off.















