Owner's library Kia Seltos Manuals Owner's manual pages, service notes, maintenance references and practical Kia Seltos help in one clean library.

Kia Seltos reference pages

Manuals, maintenance notes and quick owner help.

Find Kia Seltos operating instructions, warning light explanations, service information and owner guidance without digging through a full PDF.

Kia Seltos: Body Electrical System / Ignition Switch Assembly

Contents:

Ignition Switch On Vehicle Inspection

On Vehicle Inspection
Diagnosis with KDS
1.
The body electrical system can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
(1)
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
Information    
Refer to the KDS screen for operating conditions and details.

Ignition Switch Removal and Installation

Removal
Ignition Lock Switch Assembly
1.
Remove the crash pad center garnish.
(Refer to Body - "Crash Pad Garnish")
2.
Remove the steering column shroud panel.
(Refer to Body - "Steering Column Shroud Panel")
3.
Disconnect the key warning switch connector (A) and ignition switch connector (B).

Body Electrical System — Ignition Switch Assembly / Ignition Switch / Removal and Installation / Removal illustration

4.
Remove the ignition switch (A) by removing the clamp (B) after removing the bolts.

Tightening torque :
6.9 - 12.7 N·m (0.7 - 1.3 kgf·m, 5.1 - 9.4 lb·ft.)

Body Electrical System — Ignition Switch Assembly / Ignition Switch / Removal and Installation / Removal illustration

Key Lock Cylinder
1.
Disconnect the negative battery terminal.
2.
Remove the steering column upper & lower shroud panel.
(Refer to Body - "Steering Column Shroud Panel")
3.
Insert key and turn it to ACC position.
4.
Disconnect the connector (A).

Body Electrical System — Ignition Switch Assembly / Ignition Switch / Removal and Installation / Removal illustration

5.
Remove the key lock cylinder (A) after pushing the lock pin (B).

Body Electrical System — Ignition Switch Assembly / Ignition Switch / Removal and Installation / Removal illustration

Installation
1.
Install in reverse order of removal.
Note    
•
The existing shear bolts must be replaced with a new one. (Do not reuse it.)
•
Tighten the shear bolts until its head is cut off.

Body Electrical System — Ignition Switch Assembly / Ignition Switch / Removal and Installation / Installation illustration

Ignition Switch Inspection

Inspection
1.
Disconnect the negative ( - ) battery terminal.
2.
Disconnect the key warning switch connector (A) and ignition switch connector (B).

Body Electrical System — Ignition Switch Assembly / Ignition Switch / Inspection illustration

3.
Check for continuity between the terminals.

Body Electrical System — Ignition Switch Assembly / Ignition Switch / Inspection illustration

Other information:

Kia Seltos SP2 (2021-2026) Service Manual: Installation

Special Service Tool Tool Name / Number Illustration Description Oil seal installer09452 - 26100 Used for IVT transmission case and housing oil seal installation [2WD](Used with the handle) Oil seal installer09453 - 3L241 Used for IVT transmission case oil seal installation [4WD](Used with the handle) Oil seal installer09453 - 2W100 Used for IVT transmission housing oil seal installation [4WD](Used with the handle) Handle09231 - H1100 Used with the oil seal installer Installation 1.

Kia Seltos SP2 (2021-2026) Service Manual: LCD display

The Kia Seltos LCD display modes can be changed using the control buttons on the steering wheel. These modes provide access to driving information, vehicle settings, warning messages, and system status screens. LCD Display Control : MODE button for changing display modes / : MOVE switch for changing items OK: SELECT/RESET button for selecting, confirming, or resetting the highlighted item