Kia Seltos SP2 (2021-2026) Service Manual / Intelligent Variable Transmission (IVT) System
Kia Seltos: Intelligent Variable Transmission (IVT) System
Contents:
- Single-Use Parts
- Specification
- Special Service Tools
- Troubleshooting
- IVT Control System
- Intelligent Variable Transmission (IVT)
- Hydraulic System
Single-Use Parts
| Single-Use Parts |
Non-reusable parts (Single-Use Parts)
Workshop manual provides “Components and Components Location� which can be used to identify “Non-reusable parts�.
When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be
replaced. Kia Non-reusable parts are designed to be installed only once.
Before working on a vehicle, check “Components and Components Location� to find the non-reusable parts in a
system.
※ Symbol of Non-reusable parts
|
Symbol |
Meaning |
|
|
Do not reuse the part. Replace with a new one. |
※ Example of “Components and Components Location�

Specification ➤
Special Service Tools
| Special Service Tool |
|
Tool Name / Number |
Illustration |
Description |
| Engine support fixture (bar) 09200 - 3N000 |
|
Used for holding engine assembly when removing / installing IVT transmission ※Refer to the engine support fixture assembly drawing below |
| Engine support fixture (supporter) 09200 - 2S000 09200 - 2S200 |
|
Used for holding engine assembly when removing / installing IVT
transmission (09200- 2S100 is unnecessary) ※Refer to the engine support fixture assembly drawing below |
|
Engine support fixture (front supporter) 09200 - C3610 |
|
Used for holding engine assembly when removing / installing IVT transmission ※Refer to the engine support fixture assembly drawing below |
| Engine support fixture (adapter) 09200 - 4X000 |
|
Used for holding engine assembly when removing / installing IVT transmission ※Refer to the engine support fixture assembly drawing below |
| Oil seal installer 09452 - 26100 |
|
Used for IVT transmission case and housing oil seal installation [2WD] (Used with the handle) |
|
Oil seal installer 09453 - 3L241 |
|
Used for IVT transmission case oil seal installation [4WD] (Used with the handle) |
|
Oil seal installer 09453 - 2W100 |
|
Used for IVT transmission housing oil seal installation [4WD] (Used with the handle) |
|
Handle 09231 - H1100 |
|
Used with the oil seal installer |
| Position switch guide pin 09480 - A3800 |
|
Used for fixing N range when installing position switch |
※ Engine support fixture assembly drawing
Troubleshooting
| Troubleshooting |
| Limp Home Mode |
Limp Home Mode features a fail-safe function that prevents dangerous situations in the event of a transmission
failure. The vehicle will be driven in limp home mode if the IVT transmission malfunctions. In this mode, the
transmission operates at a minimal functionality level (fixed shifting, limited shifting, reverse, neutral), making
it possible for the vehicle to reach a service center.
|
| Warning lamp ON |
|
Condition |
Suspected Cause |
Remedy |
|
Vehicle Stopped |
Electric parts fault (Speed sensor, Solenoid valve, Position switch, E-Module, etc) |
Replace the electric parts |
| Malfunction when changed condition from stop (Including defective engine start) |
|
Condition |
Suspected Cause |
Remedy |
| Vehicle Stopped |
Position switch fault |
Inspect the position switch and connector |
| Unable to drive/reverse |
|
Condition |
Suspected Cause |
Remedy |
| Vehicle Stopped |
1. Check driven pulley pressure sensor at static condition using the KDS : 0 bar / Check Oil pump seizure (shaft sticking) 2. P0731 / P0730 / P0867 warning lamp ON 3. Broken pulley chain belt 4. Damaged gear/clutch/brake |
Replace the IVT |
| Unable to P range released |
|
Condition |
Suspected Cause |
Remedy |
|
Vehicle Stopped |
Parking system (sprag fault sticking) |
Replace the IVT |
| Delay / jerk (When the damper is engaged) |
|
Condition |
Suspected Cause |
Remedy |
| Driving condition |
1. Damper clutch control solenoid valve fault 2. Valve body fault 3. Broken pulley chain belt 4. Damaged gear/clutch/brake |
1. Replace the damper clutch control solenoid valve 2. Replace the valve body 3. Inspect/replace sealing 4. Check the oil level |
| IVT fluid smell inflow |
|
Condition |
Suspected Cause |
Remedy |
| Driving condition |
1. Incorrect fluid level 2. Cooling system fault |
1. Check the fluid level 2. Inspect the engine cooling system |
| Fluid suction noise |
|
Condition |
Suspected Cause |
Remedy |
|
Driving condition |
Low fluid level (leakage, incorrect repair) |
After checking the fluid leakage from the IVT case or the valve body cover, inspect the fluid level. |
| Shifting gear trouble |
|
Condition |
Suspected Cause |
Remedy |
| Driving condition |
Drive pulley speed sensor fault |
Inspect the drive pulley speed sensor and connector |
|
Driven pulley speed sensor fault |
Inspect the driven pulley speed sensor and connector |
|
|
Turbine speed sensor fault |
Inspect the turbine speed sensor and connector (E-module) |
|
|
Solenoid valve fault |
Inspect the solenoid valve |
|
|
CAN communication fault |
Inspect the CAN communication line and controller (TCM/ECM) |
|
| TCM software fault |
1. Inspect the TCM and replace it if necessary 2. After replacement, input oil characteristics and perform TCM adaptive value learning |
|
|
TCM learning not performed |
Perform the learning procedure again after resetting "AUTO T/A learning value" |
|
|
E-Module fault |
Inspect the E-module & connector |
|
|
Poor hydraulic pressure control |
Inspect the IVT hydraulic pressure |
|
|
Poor hydraulic pressure supply |
Inspect the oil level |
|
|
Not performed oil characteristics input after replacement of TCM or IVT |
Input the oil characteristics |
|
|
Slipping in the IVT, Damaged clutch/brake |
Replace the IVT |
|
|
Position switch fault |
Inspect the position switch and connector |
| Shifting shock |
|
Condition |
Suspected Cause |
Remedy |
| Driving condition |
Bad TCM learning value |
Perform the learning procedure again after resetting "AUTO T/A learning value" |
|
Not performed oil characteristics input after replacement of TCM or IVT |
Input the oil characteristics |
|
|
Low fluid level (leakage, incorrect repair) |
After checking the fluid leakage from the IVT case or the valve body cover, inspect the fluid level. |
|
|
Incorrect installation of the IVT |
Tighten the mounting bolts with the specified torque |
|
|
Damaged gear/clutch/brake |
Replace the IVT |
| Abnormal noise from transmission |
|
Condition |
Suspected Cause |
Remedy |
| Driving condition |
Damaged bearing / parts stuck inside |
Replace the IVT |
|
Low oil level |
Inspect the oil level |
IVT Control System ➤
Intelligent Variable Transmission (IVT) ➤
Hydraulic System ➤
Other information:
Kia Seltos SP2 (2021-2026) Service Manual: Vehicle Auto Shut-off system
The Vehicle Auto Shut-off system in the Kia Seltos is designed to turn the vehicle off automatically after a selected period of time. This feature helps reduce unnecessary fuel use and energy consumption, and it also helps lower the risk of carbon monoxide (CO) exposure when the vehicle is left running while parked.Kia Seltos SP2 (2021-2026) Service Manual: Tire terminology and definitions
Refer to the following definitions for tire-related terms commonly found in the Kia Seltos tire description, tire placard, sidewall markings, and maintenance information. Air Pressure: The amount of air inside the tire pressing outward against the tire structure. Air pressure is measured in pounds per square inch (psi) or kilopascals (kPa). Accessory Weight: The combined weight of optional accessories installed on the vehicle.

