Owner's library Kia Seltos Manuals Owner's manual pages, service notes, maintenance references and practical Kia Seltos help in one clean library.

Kia Seltos reference pages

Manuals, maintenance notes and quick owner help.

Find Kia Seltos operating instructions, warning light explanations, service information and owner guidance without digging through a full PDF.

Kia Seltos: All Wheel Drive (AWD) System / Propeller Shaft Assembly

Contents:

Propeller Shaft Components and Components Location

All Wheel Drive (AWD) System — Propeller Shaft Assembly / Propeller Shaft / Components and Components Location / Propeller Shaft Assembly / Propeller Shaft / Components and Components Location illustration

1. Front Transfer Assembly
2. Front Propeller Shaft
2-a. 49.0 - 68.6 N·m (5.0 - 7.0 kgf·m, 36.2 - 50.6 lb·ft)
3. Center Bearing Bracket
3-a. 49.0 - 68.6 N·m (5.0 - 7.0 kgf·m, 36.2 - 50.6 lb·ft)
4. Rear Tube
4-a. 60.8 - 65.7 N·m (6.2 - 6.7 kgf·m, 44.8 - 48.5 lb·ft)
5. Coupling Assembly and Rear Differential Carrier Assembly

Propeller Shaft On Vehicle Inspection

Inspection
1.
Shift gear to neutral or 'N'.
2.
Lift up the vehicle.
3.
Check the CV joint boot for damage. Replace the propeller shaft in case of excessive damage.
4.
Check the CV joint for excessive free play or noise. If excessive free play or noise occurs, replace the propeller shaft.

Propeller Shaft Removal and Installation

Removal
1.
Remove the front sub frame under cover (A) after removing the bolts.

Tightening torque :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

All Wheel Drive (AWD) System — Propeller Shaft Assembly / Propeller Shaft / Removal and Installation / Removal illustration

2.
Mark the front transfer assembly and propeller shaft mounting position and then remove the mounting bolts (A).

Tightening torque :
49.0 - 68.6 N·m (5.0 - 7.0 kgf·m, 36.2 - 50.6 lb·ft)

All Wheel Drive (AWD) System — Propeller Shaft Assembly / Propeller Shaft / Removal and Installation / Removal illustration

Note    
•
Do not reuse the front propeller shaft mounting bolts.
•
If the direction of mounting bolts, washers and propeller shafts is assembled differently from the initial state, abnormal vibration may occur at high speed due to propeller shaft imbalance.
•
If the propeller shaft is replaced with a new one or there is abnormal vibration, balance the propeller shaft with a propeller shaft balancing equipment.
•
If the front propeller shaft mounting bolts are removed and neglected without a jack, internal damage can occur. support the propeller shaft with a jack.
3.
Mark the rear tube rubber coupling and rear differential companion mounting position (A), and then remove the mounting bolts (B).

Tightening torque :
49.0 - 68.6 N·m (5.0 - 7.0 kgf·m, 36.2 - 50.6 lb·ft)

All Wheel Drive (AWD) System — Propeller Shaft Assembly / Propeller Shaft / Removal and Installation / Removal illustration

Note    
•
Do not reuse the rear tube mounting bolts.
•
If the direction of mounting bolts, washers and propeller shafts is assembled differently from the initial state, abnormal vibration may occur at high speed due to propeller shaft imbalance.
•
If the rear tube mounting bolts are removed and neglected without a jack, internal damage can occur. support the propeller shaft with a jack.
4.
Remove the center bearing bracket mounting bolts, and then remove the propeller shaft (A).

Tightening torque :
49.0 - 68.6 N·m (5.0 - 7.0 kgf·m, 36.2 - 50.6 lb·ft)

All Wheel Drive (AWD) System — Propeller Shaft Assembly / Propeller Shaft / Removal and Installation / Removal illustration

Note    
•
Mark the position of the propeller shaft mounting bolt to prevent incorrect installation.
•
If the direction of mounting bolts, washers and propeller shafts is assembled differently from the initial state, abnormal vibration may occur at high speed due to propeller shaft imbalance.
Installation
1.
Install in reverse order of removal.

Other information:

Kia Seltos SP2 (2021-2026) Service Manual: Air Conditioner Refrigerant/Compressor Refrigerant Recovery/Recycling/Charging/Vacuum

Refrigerant Recovery/Recycling/Charging/Vacuum (R-134a) Equipped with R-134a recovery/recycling/charging equipment 1. Connect the R-134a recovery/recycling/charging equipment to the high-pressure service port (A) and low-pressure service port (B) by reading the refrigerant recovery/recycling/charging equipment instruction manual.

Kia Seltos SP2 (2021-2026) Service Manual: Tightening Torque

Tightening Torque Engine and Transaxle Assembly Engine Room Under Cover Item N·m kgf·m lb·ft lb·in Engine room under cover bolt 7.