Owner's library Kia Seltos Manuals Owner's manual pages, service notes, maintenance references and practical Kia Seltos help in one clean library.

Kia Seltos reference pages

Manuals, maintenance notes and quick owner help.

Find Kia Seltos operating instructions, warning light explanations, service information and owner guidance without digging through a full PDF.

Kia Seltos: Engine Mechanical System

Contents:

Single-Use Parts

Single-Use Parts
Non-reusable parts (Single-Use Parts)
Workshop manual provides “Components and Components Location� which can be used to identify “Non-reusable parts�. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once.
Before working on a vehicle, check “Components and Components Location� to find the non-reusable parts in a system.
※ Symbol of Non-reusable parts
Symbol
Meaning

Engine Mechanical System — Single-Use Parts illustration

Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location�

Engine Mechanical System — Single-Use Parts illustration

Specification ➤

Compression Pressure Inspection

Compression Pressure Inspection
Note    
If the there is lack of power, excessive oil consumption or poor fuel economy, measure the compression pressure.
1.
Start the engine, run it so that the coolant temperature is 80 - 95°C (176 - 203°F), then stop.
2.
Remove the engine cover.
(Refer to Engine and Transaxle Assembly - "Engine Cover")
3.
Disconnect the injector connector (A).

Engine Mechanical System — Compression Pressure Inspection illustration

4.
Remove the ignition coil.
(Refer to Engine Electrical System - "Ignition Coil")
5.
Remove the spark plug.
(Refer to Engine Electrical System - "Spark Plug")
6.
Check the cylinder compression pressure.
(1)
Insert a compression gauge into the spark plug hole.

Engine Mechanical System — Compression Pressure Inspection illustration

(2)
Crank the engine over 20 times to measure compression pressure.
Note    
Always use a fully charged battery to obtain engine speed of 200 rpm or more.
(3)
Repeat the process from (1) to (3) for each cylinder and measure.
Note    
This measurement must be taken in as short a time as possible.

Compression pressure
Minimum pressure :
1,275 kPa (13.0 kgf/cm², 185 psi)
Difference between each cylinder :
98 kPa (1.0 kg/cm², 14 psi) or less

(4)
If the compression pressure of the one or more cylinders is lower than the service limit, fill a small amount of engine oil through the cylinder ignition plug hole and repeat (1) to (3) for remeasurment.
•
If the compression pressure rises due to the addition of engine oil, the piston ring or cylinder wall may have been worn and damaged.
•
If the compression pressure does not rise, the valve may have worn out, the valve seat may not be in good contact, or gas may have leaked due to poor gasket.
7.
Install the spark plug.
(Refer to Engine Electrical System - "Spark Plug")
8.
Install the ignition coil.
(Refer to Engine Electrical System - "Ignition Coil")
9.
Install the injector connectors (A).

Engine Mechanical System — Compression Pressure Inspection illustration

10.
After the above verification, some DTC codes may occur.
In this case, the DTC code will be erased as KDS.
11.
Install the engine cover.
(Refer to Engine and Transaxle Assembly - "Engine Cover")

Troubleshooting ➤

Special Service Tools

Special Service Tool
Tool Name / Number
Illustration
Description
Crankshaft front oil seal installer
09231-2E000

Engine Mechanical System — Special Service Tools / Special Service Tool illustration

Used for installing crankshaft front oil seal
Valve stem seal installer
09222-2E000

Engine Mechanical System — Special Service Tools / Special Service Tool illustration

Used for installing valve stem seal
Valve spring compressor
09222-3K000
09222-3K100

Engine Mechanical System — Special Service Tools / Special Service Tool illustration

Used for removing installing intake or exhaust valve
09222-3K000 (Compressor)
09222-3K100 (Holder)
Crankshaft rear oil seal installer
09214-2E000
09231-H1100

Engine Mechanical System — Special Service Tools / Special Service Tool illustration

Used for installing crankshaft rear oil seal
09214-2E000 (Installer)
09231-H1100 (Handle)
Ring gear stopper
09231-2B100
09231-3N100

Engine Mechanical System — Special Service Tools / Special Service Tool illustration

Used for removing / intalling crankshaft damper pulley
Ring gear stopper
09231-3D100
09231-2W100

Engine Mechanical System — Special Service Tools / Special Service Tool illustration

Used for removing / intalling crankshaft damper pulley
Oil pan remover
09215-3C000

Engine Mechanical System — Special Service Tools / Special Service Tool illustration

Removal of oil pan
Oil filter wrench
09263-2E000

Engine Mechanical System — Special Service Tools / Special Service Tool illustration

Used for removing and installing oil filter
Steel ball installer
0K221-2M100

Engine Mechanical System — Special Service Tools / Special Service Tool illustration

Used for installing steel ball
HLA air bleed tool
0K246 - L8000

Engine Mechanical System — Special Service Tools / Special Service Tool illustration

Used to air bleed HLA

Cooling System ➤

Cylinder Block ➤

Cylinder Head Assembly ➤

Drive Belt System ➤

Engine and Transaxle Assembly ➤

Intake and Exhaust System ➤

Lubrication System ➤

Timing System ➤

Other information:

Kia Seltos SP2 (2021-2026) Service Manual: Alternator On Vehicle Inspection

On Vehicle Inspection Electrical Specified Value Inspection (Using the Voltmeter and Ammeter) 1. Voltage Drop Test Of Alternator Output Wire This test is to check the wiring condition between the alternator B terminal and the battery ( + ) terminal by using the voltage drop of the wiring.

Kia Seltos SP2 (2021-2026) Service Manual: Engine coolant

The Kia Seltos high-pressure cooling system uses a reservoir filled with year-round antifreeze coolant. This coolant is installed at the factory and is designed to help protect the engine from overheating, freezing, and internal corrosion. Check the antifreeze protection and coolant level at least once a year, preferably at the beginning of the winter season, and before driving the Kia Seltos to a colder climate.